Abstract:The effects of cold rolling followed by annealing on the mechanical properties and dislocation substructure evolution of undoped and 1.1 at. % carbon-doped Fe40.4Ni11.3Mn34.8Al7.5Cr6 high entropy alloys (HEAs) have been investigated. X-ray diffraction, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atom probe tomography (APT) were employed to characterize the microstructures. The as-cast HEAs were coarse-grained and single phase f.c.c., whereas the thermomechanical treatment caused recrystallization (to fine grain sizes) and precipitation (a B2 phase for the undoped HEA; and a B2 phase, and M23C6 and M7C3 carbides for the C-doped HEA). Carbon, which was found to have segregated to the grain boundaries using APT, retarded recrystallization. The reduction in grain size resulted in a sharp increase in strength, while the precipitation, which produced only a small increase in strength, probably accounted for the small decrease in ductility for both undoped and C doped HEAs. For both undoped and C-doped HEAs, the smaller grain-sized material initially exhibited higher strain hardening than the coarse-grained material but showed a much lower strain hardening at large tensile strains. Wavy slip in the undoped HEAs and planar slip in C-doped HEM were found at the early stages of deformation irrespective of grain size. At higher strains, dislocation cell structures formed in the 19 urn grain-sized undoped HEA, while microbands formed in the 23 mu m grain-sized C-doped HEA. In contrast, localized dislocation clusters were found in both HEM at the finest grain sizes (5 mu m). The inhibition of grain subdivision by the grain boundaries and precipitates lead to the transformation from regular dislocation configurations consisting of dislocation-cells and microbands to irregular dislocation configurations consisting of localized dislocation clusters, which further account for the decrease in ductility. Investigation of the formation mechanism and strain hardening of dislocation cells and microbands could benefit future structural material design. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Effect of Thermomechanical Processing on Microstructure and Mechanical Properties of CoCrFeNiMn High Entropy Alloy

Effect of Cold Rolling on Microstructure and Mechanical Property of a Novel (fe50mn30co10cr10)97c2mo1 High Entropy Alloy

Effect of partial recrystallization on microstructure and tensile properties of NiFeCoCrMn high-entropy alloy

Effect of Heat Treatment on Microstructure and Properties of CoCrFeMnNi-5％Mo High Entropy Alloy

Partially Recrystallized Structure and Mechanical Properties of CoCrFeNiMo0.2 High-Entropy Alloy

Microstructure Evolution and Mechanical Property of Directionally Solidified CoCrFeMnNi High Entropy Alloy

The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy

Microstructure and Properties of Bulk Al0.5CoCrFeNi High-Entropy Alloy by Cold Rolling and Subsequent Annealing

Investigation on Microstructure, Superior Tensile Property and Its Mechanism in Al0.3CoCrFeNi High-Entropy Alloy Via Thermo-Mechanical Processing

The Effect of Carbon on the Microstructures, Mechanical Properties, and Deformation Mechanisms of Thermo-Mechanically Treated Fe40.4Ni11.3Mn34.8Al7.5Cr6 High Entropy Alloys

Effect of Temperature and Strain Rate on Quasi-Static and Dynamic Compressive Behavior of Forged CrMnFeCoNi High Entropy Alloy

Enhancing mechanical properties of Al0.25CoCrFeNi high-entropy alloy via cold rolling and subsequent annealing

Effect of cold working and annealing on microstructure and properties of powder metallurgy high entropy alloy

Microstructure and Mechanical Properties of High-Carbon-Containing Fe-Ni-Mn-Al-Cr High-Entropy Alloy: Effect of Thermomechanical Treatment

Microstructure and properties of bulk Al 0.5 CoCrFeNi high-entropy alloy by cold rolling and subsequent annealing

Studying the Effect of Cold Rolling and Heat Treatment on the Microstructure and Mechanical Properties of the Fe36Mn20Ni20Cr16Al5Si3 High Entropy Alloy

Recrystallization Tuning to Optimize Mechanical Properties in Heavily Rolled CoCrFeNi Medium Entropy Alloy

Effects of Thermo-mechanical Treatment on the Microstructures and Mechanical Properties of a Medium-Entropy Alloy

Microstructure Evolution and Tensile Property of a CuMnFeCoNi High-Entropy Alloy During Thermomechanical Treatment

Effect of Rolling Process on Deformation Structure and Mechanical Properties of Cocrfenimo0.35 High Entropy Alloy

Effect of Annealing Temperature on the Microstructure and Mechanical Properties of CoCrFeNiNb0.2Mo0.2 High Entropy Alloy