Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

High-temperature Deformation Behavior of Cu–6.0Ni–1.0Si–0.5Al–0.15 Mg–0.1Cr Alloy

Hot Deformation Behavior and Microstructure Evolution of Cu–Ni–Co–Si Alloys

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Microstructure evolution and hot deformation behavior of Cu−3Ti−0.1Zr alloy with ultra-high strength

The Microstructure Evolution and Dynamic Recrystallization Mechanism of Cu-1.1–Ni-0.7–Co-0.45–Si-0.3Cr Alloys during High-Temperature Deformation

Microstructure and hot deformation behavior of the Cu-1Ni-0.9Sn-0.5Ti-0.3Cr alloy

EBSD analysis of hot deformation behavior of Cu-Ni-Co-Si-Cr alloy

High-temperature deformation behavior of a novel high strength and high elasticity Cu–20Ni–20Mn–0.3Nb–0.3Cr–0.1Zr alloy

Hot Deformation Behavior and Microstructure Evolution of Al-7.92 Zn-1.64 Mg-2.00 Cu Alloy

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Hot Deformation Behavior of Homogenized Al-7.8Zn-1.65Mg-2.0Cu (wt.%) Alloy

Study on Hot Compression Deformation and Processing Map of Mg-6Al-2Si-1.5Er Mg Alloy

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

Hot Deformation Behavior and Processing Map of Al-Zn-Mg-Cu-Zr Alloy

Microstructure Evolution and Hot Deformation Behavior of a CuNiSn Alloy

Investigation on hot deformation behavior of 2050 Al-Cu-Li alloy

Hot Deformation Behavior and Finite Element Simulation of Mg–8.3Gd–4.4Y–1.5Zn–0.8Mn Alloy

Deformation Behavior and Constitutive Model for High Temperature Compression of a Newly Type of Ni3Al‐based Superalloy

Hot deformation behavior and process parameters optimization of GH4738 nickel-based superalloy

Hot Deformation Behavior and Processing Maps of an As-Cast Al-5Mg-3Zn-1Cu (wt%) Alloy