Abstract:Modern aero and power industry needs high-performance gas turbine. Directional solidification (DS) columnar grain and single crystal (SX) blade as key parts of gas turbine serve in heavy stress and high temperature conditions. The DS and SX blade are mainly produced by high rapid solidification (HRS) method, and HRS is one of useful DS technology, which has a property that the heat dissipating ways are changing during the process and the temperature gradients will vary correspondingly. The dendrite grain arrays were the substructure of a DS or SX blade. The structure of the dendrite grain arrays influences the mechanical property of the final casting very much, but is seriously affected by the solidification parameters, such as temperature gradient. In this work, the dendrite grain growth of DD6 superalloy was studied based on cellular automaton- finite difference (CA-FD) model concerning the HRS method's macro solidification parameters. Mathematic models for dendrite grain growth controlled by temperature field and solute field were built to describe the competitive growth and morphology evolution of dendrite grains. Then the dendrite calculation model was coupled with the models of DS process calculation, and some HRS solidification parameters were included, such as withdrawal rate, pouring temperature, etc. The coupled models were used to predict the dendrite grain competitive growth of DD6 superalloy during the DS process. The variation of solute distribution and the dynamic adjustment of dendritic spacing during the process could be predicted by simulating calculation. The DS experiment was carried out with a cylinder sample, and dendrite grains' distribution in the transverse and longitude section was observed by OM and SEM. Then the simulated dendritic morphology was compared with that by experiment. The primary and secondary dendritic spacing by experiment and simulation were measured, and the compared results revealed that as the DS process going on the temperature gradient decreased gradually and the primary dendritic spacing was increasing. So simulation results of the DS dendritic competitive growth were validated by the experiment results, and the proposed models could predict the dendrite grain morphology and the adjustments of DS dendritic spacing of DD6 superalloy very well.

Primary Dendrite Trunk Diameter in Al-7wt% Si Alloy Directionally Solidified Aboard the International Space Station

Experimental and simulation of primary dendrite spacing in directional solidification of Al-7Si-0.36Mg alloy

Thermal and Solute Diffusion During Dendrite Growth of Mg-5wt.%Zn Alloy

Fast Synchrotron X-Ray Tomographic Quantification of Dendrite Evolution During the Solidification of Mg-Sn Alloys

The effect of cross-section geometry of castings on dendrite evolution in Mg Gd alloys by in situ X-ray radiography

Simulation on microstructure evolution of Al−Si alloy under effect of natural convection during solidification

Dendritic Evolution During Coarsening of Mg-Zn Alloys Via 4D Synchrotron Tomography

Numerical Simulation of Dendrite Growth in Ni-based Superalloy Casting During Directional Solidification Process

Influence of Solidification Parameters on the Amount of Eutectic and Secondary Arm Spacing of Al–7wt% Si Alloy Solidified under Microgravity

Dendritic segregation and arm spacing in directionally solidified CMSX-4 superalloy

Simulation of Primary Dendrite Competitive Growth and Solute Concentration Distribution in Directional Solidification DZ125 Superalloy

Synchrotron Tomographic Quantification of the Influence of Zn Concentration on Dendritic Growth in Mg-Zn Alloys

On the dendrite deformation and evolution mechanism of Ni-based superalloy during directional solidification

Numerical Modeling of Microstructure Evolution and Dendrite Growth for Al-Si Alloy Casting During Low Pressure Die Casting

Study of Dendrite Growth with Natural Convection in Superalloy Directional Solidification Via a Multiphase-Field-lattice Boltzmann Model

Dendritic Si growth morphologies in highly undercooled Al-Si alloys

Dendritic Growth in Mg-Based Alloys: Phase-Field Simulations and Experimental Verification by X-ray Synchrotron Tomography

Numerical Simulation of Dendrite Grain Growth of Dd6 Superalloy During Directional Solidification Process

Large‐scale simulation of dendrite growth in directional solidification castings

NUMERICAL SIMULATION OF DENDRITE MICROSTRUCTURE FOR Al-Si ALLOY WITH ADDITIVE PHASE

On Primary Dendritic Spacing During Unidirectional Solidification