Abstract:This paper reports a novel oscillation control algorithm for MEMS vibratory gyroscopes using a modified electromechanical amplitude modulation (MEAM) technique, which enhances the robustness against the frequency variation of the driving mode, compared to the conventional EAM (CEAM) scheme. In this approach, the carrier voltage exerted on the proof mass is frequency-modulated by the drive resonant frequency. Accordingly, the pick-up signal from the interface circuit involves a constant-frequency component that contains the amplitude and phase information of the vibration displacement. In other words, this informational detection signal is independent of the mechanical resonant frequency, which varies due to different batches, imprecise micro-fabrication and changing environmental temperature. In this paper, the automatic gain control loop together with the phase-locked loop are simultaneously analyzed using the averaging method and Routh–Hurwitz criterion, deriving the stability condition and the parameter optimization rules of the transient response. Then, a simulation model based on the real system is set up to evaluate the control algorithm. Further, the proposed MEAM method is tested using a field-programmable-gate-array based digital platform on a capacitive vibratory gyroscope. By optimizing the control parameters, the transient response of the drive amplitude reveals a settling time of 45.2 ms without overshoot, according well with the theoretical prediction and simulation results. The first measurement results show that the amplitude variance of the drive displacement is 12 ppm in an hour while the phase standard deviation is as low as 0.0004°. The mode-split gyroscope operating under atmospheric pressure demonstrates an outstanding performance. By virtue of the proposed MEAM method, the bias instability and angle random walk are measured to be 0.9° h−1 (improved by 2.4 times compared to the CEAM method) and 0.068° (√h)−1 (improved by 1.4 times), respectively.

Free Damped Oscillation Measurement Method for the Nonlinear Features of Micromechanical Gyroscopes

A Stepped Frequency Sweeping Method For Nonlinearity Measurement Of Microresonators

Eigen Frequency Measurements of a Fiber Optic Gyroscope Based on a Staircase Waveform with Large Temperature Range.

Nonlinearity Measurement for Low-Pressure Encapsulated MEMS Gyroscopes by Transient Response

Constant-frequency Oscillation Control for Vibratory Micro-Machined Gyroscopes

Frequency Characteristic Measurement of a Fiber Optic Gyroscope Using a Correlation Spectrum Analysis Method Based on a Pseudo-Random Sequence

A MICROMECHANICAL MODE-MATCHED GYROSCOPE USING STIFFNESS NONLINEARITY AND ELECTROSTATIC TUNING

Performance Characterization of a Bulk Micromachined Gyroscope Working at Atmosphere

Open-loop Operation Experiments in a Resonator Fiber-Optic Gyro Using the Phase Modulation Spectroscopy Technique.

A Simple Discussion For Undamped Duffing Impact Oscillator

An Open-Loop Test of a Resonator Fiber Optic Gyro

Resonant Fiber Optic Gyro Based on A Sinusoidal Wave Modulation and Square Wave Demodulation Technique

Synchronous Digital Quadrature Demodulation Technique For Resonant Optic Gyroscopes

A novel oscillation control for MEMS vibratory gyroscopes using a modified electromechanical amplitude modulation technique

Multifrequency Excitation Method for Rapid and Accurate Dynamic Test of Micromachined Gyroscope Chips

Nonlinear vibration and amplitude ratio output performance of a resonant micro-gyroscope based on bifurcation detection

A Novel Microelectromechanical Resonant Gyroscope

Performance Research of a Vibratory Wheel Micromechanical Gyroscope

Nonlinear damping in a micromechanical oscillator

Tuning the primary resonance of vibrating beam micro-gyroscopes based on piezoelectric actuation and nonlinearity in curvature and inertia

A Novel Mechanical Frequency Tuning Method Based on Mass-Stiffness Decoupling for MEMS Gyroscopes