Abstract:The recycling of lithium iron phosphate power batteries that have exploded in retirement is urgent, but the focus and difficulty of the recycling is the effective recovery of lithium and iron elements in the cathode active material. In this study, the cathode sheets and other components of the lithium-ion batteries were obtained by pretreatment, and the cathode active material and the Al foil of the collector were recovered by stirring with dilute alkali solution (optimized conditions of alkali solution concentration 0.075 mol L-1, liquid-solid ratio 20 mL g(-1), and stirring time 40 min). The H2SO4-H2O2 system was used to leach used lithium iron phosphate cathode powder, the leaching process conditions were optimized and the leaching mechanism was revealed. The leaching rates of Li and Fe elements reached 98.79 % and 94.97 %, respectively, at a H2SO4 concentration of 2.5 mol L-1, a H2O2 dosage of 6 mL, a liquid-solid ratio of 25 mL g(-1), a leaching temperature of 60 degrees C and a leaching time of 60 min. The pH value was precisely adjusted in the chemical precipitation method to recover lithium and iron elements from cathode active material. The recovered products FePO4 and Li2CO3 were used as the precursors for the regeneration of LiFePO4 cathode material. The electrochemical performance of LiFePO4/C materials regenerated at 700 degrees C from the raw material with a lithium to iron molar ratio of 1.03:1 was relatively good, with a first discharge specific capacity of 160.1 mAh g(-1) at 0.1 C, and a charge/discharge efficiency of 96.70 % for the first cycle. The good electrochemical performance was still maintained at a higher rate, with a capacity retention of 99.7 % after 100 cycles at 1 C.

Regeneration of Black Powders of Waste Lithium Iron Phosphate Battery Produced by Large‐Scale Industrialization

A Facile Route for the Efficient Leaching, Recovery, and Regeneration of Lithium and Iron from Waste Lithium Iron Phosphate Cathode Materials

Regenerated LiFePO4/C for scrapped lithium iron phosphate powder batteries by pre-oxidation and reduction method

Direct Regeneration of High-Value LiFePO 4 Cathode Materials with Nitrogen Doped Carbon Coating

A Sustainable Closed-Loop Process of Oxidation Leaching and Regeneration for Lithium Iron Phosphate Materials from Spent Batteries

Environmental-friendly low-cost direct regeneration of cathode material from spent LiFePO 4

Closed-loop regeneration of LiFePO4 from spent lithium-ion batteries: A “feed three birds with one scone” strategy toward advanced cathode materials

Regenerating LiFePO4/C Using Recycled LiH2PO4 As Raw Material

Simultaneous anodic de-lithiation/cathodic lithium-embedded regeneration method for recycling of spent LiFePO 4 battery

Direct Recycling Strategy for Spent Lithium Iron Phosphate Powder: an Efficient and Wastewater-Free Process

Interfacial Metal-Solvent Chelation for Direct Regeneration of LiFePO4 Cathode Black Mass.

Direct Regeneration of Industrial LiFePO4 Black Mass Through A Glycerol‐Enabled Granule Reconstruction Strategy

Recycling of LiFePO 4 cathode materials: From laboratory scale to industrial production

Dual-Function Regeneration of Waste Lithium Cobalt Oxide for Stable High Voltage Cycle Performance

A sustainable closed-loop method of selective oxidation leaching and regeneration for lithium iron phosphate cathode materials from spent batteries

Direct Regeneration of Degraded LiFePO4 Cathode via Reductive Solution Relithiation Regeneration Process

Efficient Extraction of Lithium from Anode for Direct Regeneration of Cathode Materials of Spent Li-Ion Batteries

A mild closed-loop process for lithium–iron separation and cathode materials regeneration from spent LiFePO 4 batteries

Recovery and regeneration of LiFePO4 from spent lithium-ion batteries via a novel pretreatment process

A novel acid-free leaching route of recovering Li2CO3 and FePO4 from spent LiFePO4 black powder

A Multifunctional Amino Acid Enables Direct Recycling of Spent LiFePO4 Cathode Material