Abstract:With the rapid development of the third-generation semiconductor materials, an appropriate high-temperature-resistant die attach material has become one of the bottlenecks to fully exploit the excellent properties of the third-generation semiconductor power devices. At the same time, a low-bonding temperature is always the pursuit goal of packaging engineers to reduce the thermal residual stress in electronic devices. In this paper, a low-temperature bonding method was proposed to address the above-mentioned issue based on In infiltrating the nanoporous Cu. In, as a low melting point metal, can significantly reduce the bonding temperature, and the nanoporous Cu structure can provide a very large specific surface area, which greatly increases the consumption rate of In. Furthermore, the formed Cu-In IMCs with high-remelting temperature can withstand the high operating temperature. The microstructures of the bondlines before and after bonding were studied in detail. The results show that the bondline can completely consume the low melting point In, within 10 min at 165 °C under a pressure of 0.75 MPa. When the bonding temperature was further increased to 310 °C, the bondline was composed of η-Cu2In and δ-Cu7In3 phases, whose melting points were more than 600 °C. The average electrical resistivity was determined to be 5.53 ± 0.65 μΩ cm, and the thermal conductivities were 144.33 W m−1 K−1, 139.24 W m−1 K−1 and 129.79 W m−1 K−1 at 30 °C, 150 °C and 300 °C, respectively. The average shear strength were 19.09 ± 3.4 MPa, 20.47 ± 4.6 MPa and 30.73 ± 5.2 MPa at 30 °C, 250 °C, 310 °C, respectively. These results indicate that the nanoporous Cu infiltrated with In could meet the requirements of electrical, thermal conduction, and mechanical support as a die attachment for high-power devices.

Solderless Bonding with Nanoporous Copper As Interlayer for High-Temperature Applications.

Interconnection Method Based on Solder-Filled Nanoporous Copper As Interlayer for High-Temperature Applications

A Low-Temperature Cu-to-Cu Interconnection Method by Using Nanoporous Cu Fabricated by Dealloying Electroplated Cu–Zn

Effect of Various Parameters on the Shear Strength of Solid-State Nanoporous Cu Bonding in Cu–Cu Disks for Power Device Packaging

Improving Adhesion Strength and Thermal Conductivity of Nanowire Surface Fastener

Low Temperature Cu-Cu Bonding Using Copper Nanoparticles Fabricated by High Pressure Pvd

Formation and characterization of Monolithic nanoporous copper by chemical dealloying of Al-Cu alloys

Low Temperature Fine-Pitch Wafer-Level Cu-Cu Bonding Using Nanoparticles Fabricated by PVD

Bonding of Cu to Cu bulks through the low temperature sintering of Ag nanoparticle paste

A low-temperature bonding method for high power device packaging based on In-infiltrated nanoporous Cu

Highly Conductive Cu-Cu Joint Formation by Low-Temperature Sintering of Formic Acid-Treated Cu Nanoparticles

Low temperature nanojoining of silver–copper nanopaste as die attach material for high temperature packaging

Rapid and Low Temperature Sintering Bonding Using Cu Nanoparticle Film for Power Electronic Packaging

High-temperature Resistant Interconnections Formed by Ni Nanoparticles/Al Micro-particles Composite Paste for SiC Power Device Application

Sintering of Mixed CuAg Nanoparticles Pretreated by Formic Acid Vapor for CuCu Low Temperature Bonding

Ag-Sn Bimetallic Nanoparticles Paste for High Temperature Service in Power Devices

Low-Temperature Cu-Cu Bonding Using Silver Nanoparticles Fabricated by Physical Vapor Deposition

Low Temperature Bonding of Metals by Deposition of Nanoparticles at the Interface

Low Temperature Bonding Process Using Mixed Cu-Ag Nanoparticles for Electronic Packaging

Sn-enhanced high-temperature reliability of Cu/Nano-Ag/Cu joint via transient-liquid-phase bonding