Abstract:The pipelined-SAR ADC has become popular in wide-bandwidth and high-resolution applications due to its power-efficient architecture [1]. In the pursuit of higher ADC speeds while maintaining precision and power efficiency, not only does the conversion time of the SAR sub-ADC need to be shortened, but also the speed and gain of residue amplifiers (RA) need to be enhanced. Conventional solutions to these two problems, including reducing the bit-cycling time of the SAR and increasing the RA bandwidth, often require extensive power costs, leading to a degraded power efficiency. To address the speed and gain challenges, three techniques are proposed in this work. First, a continuous-time SAR-assisted detect-and-skip (CTDAS) to parallelize the MSB conversion with ADC sampling, thus cutting down the $1^{\text{st}}$-stage sampling and conversion time by 35% when compared with a conventional detect-and-skip (DAS) technique. Second, an open-then-close correlated level shifting (OCCLS) technique applied in the residue amplifier, which significantly speeds up the first phase by open-loop amplification reusing the first two high-bandwidth stages of the RA. With the aid of a detect-and-cut loop, an optimal voltage gain in the first phase is obtained across PVT variations, thus realizing an >80dB equivalent RA open-loop gain $\left(\mathrm{A}_{\mathrm{EO}}\right)$ across PVT variations. Third, a hybrid static-floating ringamp architecture is implemented to improve the noise performance of the RA and to fit in well with the OCCLS scheme. Thanks to the techniques above, the 22nm prototype achieves 70.7dB SNDR under 200MS/s while consuming 2.0mW from a 0.9V supply. It measures a best energy efficiency of 177.7dB Schreier FoM with fs >150MS/s.

A 172Db-Fom Pipelined SAR ADC Using a Regenerative Amplifier with Self-Timed Gain Control and Mixed-Signal Background Calibration

A 16-Bit 2.5-Ms/s SAR ADC with On-Chip Foreground Calibration

An 18-Bit 2MSPS SAR ADC with Double Passive Noise-Shaping Calibration

A 14-Bit 500-Ms/s Pipelined-SAR ADC in 28-Nm CMOS with Foreground and Background Calibration

A 1.5 Mw 68 Db SNDR 80 Ms/s 2<formula Formulatype="inline"> <tex Notation="TeX">$\times$</tex></formula> Interleaved Pipelined SAR ADC in 28 Nm CMOS

A 12-Bit 2.32gs/s Pipelined/sar Hybrid ADC with a High-Linearity Input Buffer.

A 348-Μw 68.8-Db SNDR 20-Ms/s Pipelined SAR ADC with a Closed-Loop Two-Stage Dynamic Amplifier

A Pipelined SAR ADC Reusing the Comparator As Residue Amplifier

A 12-Bit 110ms/s 4-Stage Single-Opamp Pipelined SAR ADC with Ratio-Based GEC Technique

A 13-Bit 312.5-Ms/s Pipelined SAR ADC with Open-Loop Integrator-Based Residue Amplifier and Gain-Stabilized Integration Time Generation

A 71.5-Db SNDR 475-Ms/s Ringamp-Based Pipelined SAR ADC with On-Chip Bit-Weight Calibration

A 13-Bit 312.5-Ms/s Pipelined SAR ADC with Integrator-type Residue Amplifier and Inter-stage Gain Stabilization Technique

A 68.5 Db-Sndr, 12.4-Fj/conv.-step, 100-Ms/s Pipelined-Sar ADC with PVT-enhanced Circuitry

A 12-Bit 1.5-Gs/s Single-Channel Pipelined SAR ADC with a Pipelined Residue Amplification Stage

A calibration-free 10.7 fJ/conv.-step 12-bit 120-MS/s pipelined SAR ADC in 40nm CMOS

9.1 A 2mW 70.7dB SNDR 200MS/s Pipelined-SAR ADC with Continuous-Time SAR-Assisted Detect-and-Skip and Open-then-Close Correlated Level Shifting.

An 11-Bit 100-Ms/s Pipelined-SAR ADC Reusing PVT-Stabilized Dynamic Comparator in 65-Nm CMOS.

A Bandwidth-Adaptive Pipelined SAR ADC with Three-Stage Cascoded Floating Inverter Amplifier.

A 12-Bit 100-Ms/s Pipelined-SAR ADC with PVT-Insensitive and Gain-Folding Dynamic Amplifier.

A 10-Bit 500-Ms/s Pipelined SAR ADC with Nonlinearity-Compensated Open-loop Amplifier and Parallel Conversion Through Comparator Reusing

9.4 A 182.3dB FoM<inf>s</inf> 50MS/s Pipelined-SAR ADC using Cascode Capacitively Degenerated Dynamic Amplifier and MSB Pre-Conversion Technique