Abstract:Thermal conductivity is the key thermal property of materials that are used in thermal protection of aircraft and energy conservation field, and its accurate test is of great significance in such fields. TCi method is a transient method of measuring thermal conductivity and effusivity, which was developed from the transient plane source method in the last decade. TCi technique has been widely used to measure the thermal conductivity of various materials due to its advantages of simple, rapid and single-side in-situ measurement. But the nominal accuracy is lack of sufficient verification within the full test ranges. Studies have found that the results of thermal conductivity measured by different methods for the same material may be different. Even if the same method and instrument are used to measure the same material, the results by using different test modes may vary significantly. The uncertainty of a dynamic test mainly comes from two aspects, theoretical assumptions of test theory and errors of determining input/output parameters. The latter one can be improved by adopting test facilities with higher precision and resolution, and the error usually can be estimated using the error transfer function. However, the uncertainty introduced by theoretical assumptions is difficult to determine and may lead to an incorrect result when the practical measurement deviates from the theoretical assumptions. For TCi method, except for the errors of determining input/output parameters, the theoretical assumptions in deducing the theory, the calibration curves and the contact resistance will affect the test accuracy. In this study, the influence of the above factors on the accuracy of thermal conductivity and effusivity determined by TCi technique are revealed quantitatively using numerical simulation. Firstly, the practical transient test process of TCi method is reproduced in the simulation with all thermophysical properties given. Secondly, the heat transfer processes of measuring foams, ceramics and metals by TCi method are simulated, and the calibration curves of thermal conductivity and effusivity of each type materials are obtained according to the corresponding temperature increase curve and the theoretical basis of TCi method. The influence of calibration curves on the test uncertainty is analyzed by comparing the calculated values of different calibration curves with the given values in the simulation. Finally, the influence of contact resistance on the test accuracy of different materials is analyzed by setting a thin layer of air between the sensor and the sample. The results show that TCi method could measure the effusivity of different materials accurately, and the different calibration curves have little influence on it. However, the results obtained by different thermal conductivity calibration curves are quite different, especially for the foam materials. The contact resistance between the sensor and the sample will decrease the test results of the high thermal conductivity material, while the effect can be ignored for foam materials. And the influence of contact resistance can be significantly reduced by adding contact agent. Due to the calibration curve and contact resistance in theoretical assumptions of TCi method will affect the test accuracy, the errors introduced by theoretical assumptions should be analyzed when adopting TCi method.

A correlation to calculate time constant of thermocouples

Real‐time Calculation of Three Core Cable Conductor Temperature Based on Thermal Circuit Model with Thermal Resistance Correction

Temperature Measurement by Thermocouple Probe: Influences of Variable Fluid Velocity on the Dynamic Characteristics of Thermocouple

Tailor-making Thermocouple Junction for Flame Temperature Measurement Via Dynamic Transient Method

Dynamic compensation by coupled triple-thermocouples for temperature measurement error of high-temperature gas flow

Dynamic Response Time and Deviation Estimate of Thermocouple During Heat-Exchange Temperature Measurement

Numerical Modeling of Steady State Errors for Shielded Thermocouples Based on Conjugate Heat Transfer Analysis

Time-accurate CFD conjugate analysis of transient measurements of the heat-transfer coefficient in a channel with pin fins

Heat transfer error analysis of high-temperature wall temperature measurement using thermocouple

Ito Thin Film Thermocouple For Transient High Temperature Measurement In Scramjet Combustor

Optimal design of E-type coaxial thermocouples for transient heat measurements in shock tunnels

A Method for Measuring Thermal Conductivity of Fluids by Using a Small Bead Thermistor.

THERMOCOUPLE ERROR ANALYSIS OF THE GAS TEMPERATURE MEASUREMENT IN POROUS MATERIALS AT HIGH TEMPERATURES

Accurate Compensation of Armored Thermocouple Based on Fireworks Algorithm

Influences of RF Magnetron Sputtering Power and Gas Flow Rate on a High Conductivity and Low Drift Rate of Tungsten-Rhenium Thin-Film Thermocouples.

Numerical analysis on the transient measurement of gas temperature in porous material using thermocouples at high temperatures

Effect of heat losses in the temperature transducer in measurements in hotshot wind tunnels

Automatic Algorithm Applied for Calculating Thermal Conductivity by Transient Plane Source Method

A numerical study of the measurement error introduced by TCi theoretical assumptions

Temperature Dependence of Constant Current Hot-Film Sensors: Investigation with Application to Temperature Correction for Wall-Shear Stress Measurements

Theoretical Calculation and Experimental Research on Thermal Time Constant of Single-core Cables