Experimental Study and FE Analysis on New Frame Joints of Concrete-Filled Steel Tube Structure

韩晓健,孙伟民,张素梅

2001-01-01

Abstract:通过有限元法 ,对钢筋混凝土双梁夹柱穿心承重销的梁柱节点进行了三维受力分析 ,并进行了模型试验 ,三维分析结果与模型试验结果十分接近。此基研究成果已应用于工程实际。

What problem does this paper attempt to address?

Numerical Analysis of Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges

Xie Xu,Chen Heng-zhi,Li Hui,Song Shi-rui

DOI: https://doi.org/10.1631/jzus.2005.a0859

2005-01-01

Abstract:The calculation of ultimate bearing capacity is a significant issue in the design of Concrete Filled Steel Tubular (CFST) arch bridges. Based on the space beam theory, this paper provides a calculation method for determining the ultimate strength of CFST structures. The accuracy of this method and the applicability of the stress-strain relationships were validated by comparing different existing confined concrete uniaxial constitutive relationships and experimental results. Comparison of these results indicated that this method using the confined concrete uniaxial stress-strain relationships can be used to calculate the ultimate strength and CFST behavior with satisfactory accuracy. The calculation results are stable and seldom affected by concrete constitutive relationships. The method is therefore valuable in the practice of engineering design. Finally, the ultimate strength of an arch bridge with span of 330 m was investigated by the proposed method and the nonlinear behavior was discussed.
EXPERIMENTAL INVESTIGATION AND NONLINEAR FINITE ELEMENT ANALYSIS ON THE BEHAVIOR OF CONCRETE-FILLED SQUARE STEEL TUBULAR COLUMN CONNECTIONS

NIE Jian-guo,QIN Kai,XIAO Yan

DOI: https://doi.org/10.3969/j.issn.1000-4750.2006.11.017

2006-01-01

Abstract:Based on the experiments of concrete-filled square steel tubular column connections with interior or exterior diaphragms under cyclic loading,3-D nonlinear finite element models were used to analyze the mechanical properties of these two types of connections using ANSYS.Based on appropriate material stress-strain relations and failure criteria,finite element analyses were conducted under monotonic loading and cyclic loading.The load-deflection curves and shear force-deformation curves by finite element analyses show good agreement with those of the experiments.Parametric analyses were conducted on the connections with exterior diaphragms to investigate the influences of compression ratio,width to thickness ratio,strength of the concrete in the square steel tube and concrete slab height.It is found that compression ratio and width to thickness ratio are more important to the connections.
Finite-element Analysis for Nonlinear Stabilities of Concrete-filled Steel Tubular Arch Bridges

JIAO Yu-Feng,YI Jian-Long,CHEN Shui-Fu

2008-01-01

Abstract:Owing to the limitation of establishing finite element model of concrete-filled steel tubular(CFST) arch bridge,the more precision model has been put forward.Namely the outer steel tubes,the inner concrete and the reinforcing steel bars have their own elements.Using this method,a CFST arch bridge's deflection curve under different load is obtained considering the material and geometric nonlinearity.The computed results are in agreement with the test data.The result shows that the method used in this paper has better adaptability and definition.
Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Zhang Zhi-cheng,Xie Xu,Zhang He,Chen Heng-zhi

DOI: https://doi.org/10.1631/jzus.2007.a0682

2007-01-01

Abstract:A convenient approach is proposed for analyzing the ultimate load carrying capacity of concrete filled steel tubular (CFST) arch bridge with stiffening girders. A fiber model beam element is specially used to simulate the stiffening girder and CFST arch rib. The geometric nonlinearity, material nonlinearity, influence of the construction process and the contribution of prestressing reinforcement are all taken into consideration. The accuracy of this method is validated by comparing its results with experimental results. Finally, the ultimate strength of an abnormal CFST arch bridge with stiffening girders is investigated and the effect of construction method is discussed. It is concluded that the construction process has little effect on the ultimate strength of the bridge.
Analytical Study of Circular Concrete-Filled Steel Tube Stub Columns under Axial Compression

肖岩,黄叙

DOI: https://doi.org/10.14006/j.jzjgxb.2011.12.022

2011-01-01

Abstract:As a fundamental mechanical problem in steel and concrete composite structures,the axial compressive behavior of concrete filled steel tube stub columns has been widely concerned by researchers worldwide.Focusing on the interaction between the steel tube and the core concrete,this paper presented a nonlinear analytical procedure using the octahedral stress-strain relationship,the corresponding failure criterion and flow rule proposed by Xiao(1989) as well as the simplified hardening model of the steel tube where the stress-strain relationship was represented by four segmental linear lines.The procedure presented in this paper followed fundamental principles of elasto-plastic mechanics to reflect main interactions between the steel tube and concrete infill.A total of sixteen interaction conditions between the concrete and steel tube were taken into consideration.The incremental nonlinear analysis was realized by coding a computer program using Visual Basic.The reasonable accuracy and efficiency of the analytical procedure was validated by comparing with existing testing results from literature.
Study Of Mechanical Performance Of Concrete-Filled Steel Tubular Joints

Juan Chen,Ju Chen,Weiliang Jin

DOI: https://doi.org/10.1201/9781315641645-208

2016-01-01

Abstract:With the development of large span and heavy load modern engineering, concrete-filled steel tubular truss and laced column structures appear constantly. The joints of these structures are mostly circular Concrete-Filled Steel Tubular (CFST) joints. In order to solve the problem of lacking of the research on the mechanical properties of CFST joints, three CFST T-joints and one Circular Hollow Section (CHS) T-joint which was used for comparing were tested under reversed cyclic axial loading, and three CFST T-joints and one CHS T-joint were tested under reversed cyclic in-plane bending loading. The failure modes and the ultimate load carrying capacities of CFST T-joints were concluded and the load-displacement hysteretic curves were also studied. The test results showed that the failure modes of CFST joints and CHS joints with the same geometry were completely different, the ultimate load carrying capacities of CFST joints were much higher than that of CHS joints, which shows that adopting a concrete-filled chord member is the most effective way to improve the strength of the unstiffened tubular joints when subjected to axial loading and in-plane bending, the energy dissipation mechanisms of CFST joints and CHS joints were completely different, but both CFST joints and CHS joints had excellent seismic performances. The energy analysis of CFST joints under differing loading conditions indicated that there was a significant distinction in terms of the energy dissipation mechanism. The axially loaded specimens dissipated energy mainly by plastic deformation of the brace, while the in-plane bending loaded specimens dissipated energy mainly by punching shear of the chord wall at the intersection area. This research can not only provide scientific basis for the design of CFST joints, but also effectively promote the application of CFST truss and laced column, and can promote the improvement and development of the design theory of concrete-filled steel structures.
Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Aoyu Jiang,Ju Chen,Weiliang Jin

2012-01-01

Abstract:A series of bending tests of thin-walled concrete-filled cold-formed steel tubes(CFST) were presented in this study. A total of 4 specimens were tested, two square specimens and two rectangular specimens, with width to wall thickness ratio ranging from 50 to 100. The failure mode and ultimate capacity of test specimens were obtained. A novel nonlinear analytical model was developed for the hin-walled CFSTs under bending. Nonlinear constitutive models of the confined concrete and steel tube, corner strength enhancement of the steel cross-sections, welding residual stress and local buckling were considered in the developed model. The predicted capacity calculated using the model proposed and it si shown that the model predictions agreed with the test result well. In addition, predictions from current AISC standard, Eurocode 4 and model proposed by other researcher were also compared with the test results.
Experimental investigation of thin-walled concrete-filled steel tube columns with reinforced lattice angle

fei xu,ju chen,weiliang jin

DOI: https://doi.org/10.1016/j.tws.2014.05.015

IF: 5.881

2014-01-01

Thin-Walled Structures

Abstract:Experimental investigation of thin-walled concrete-filled steel tube columns with reinforced lattice angle was conducted in this study. The lattice angle was designed to reinforce the concrete-filled steel tube columns by increasing the percentage of steel cross-sectional area. Column specimens having different lengths ranged from 500mm to 3500mm were tested. The behavior and strengths of concrete-filled steel tube columns with lattice angle were investigated. In addition, concrete-filled steel tube columns having the same size but without reinforced lattice angle were also tested for comparison. Material properties of the concrete and steel used in the test specimens were measured. The test strengths are compared with the design strengths calculated using the AISC Specification and Eurocode for the design of composite structural members. A new design method was also proposed for the concrete-filled steel tube columns with reinforced lattice angle. It is shown that the design predictions from the proposed method agree with test results well.
FINITE ELEMENT ANALYSIS ON CONCRETE-ENCASED CFST COLUMN TO REINFORCED CONCRETE BEAM JOINTS

D. Y. Ma,W. Li,L. H. Han,X. L. Zhao

2016-01-01

Abstract:This paper presents finite element analysis (FEA) of concrete-encased concrete-filled steel tube (CFST) column to reinforced concrete (RC) beam joints. The proposed FEA model considers the modelling for concrete in different locations, the material deterioration under cyclic loading and the interaction between steel and concrete components. The established FEA model is verified by a set of experimental results. The proposed model is found to have reasonable accuracy by comparisons with the test data. The FEA model is then used to perform the full-range analysis of tzzhe composite joint. It is found that the development of the plastic hinge is affected by the stress of longitudinal bar. Moreover, the bracket is capable of improving the shear and flexural resistance of the composite joint.
Experimental study on seismic behaviors of a new type of frame joint between concrete-filled rectangular steel tubular columns and steel beams

于旭,刘伟庆,葛卫

DOI: https://doi.org/10.3969/j.issn.1000-1301.2004.06.014

2004-01-01

Abstract:Test results of a new type of joint between concrete-filled rectangular steel tubular columns and steel beams under reversed cyclic loads are presented in this paper. The seismic behaviors of frame joints are affected by concrete cores, length of stiffener and relative dimensions of column to beam. The relative design suggestions are proposed.
FE modeling analysis of the joints with diagonal concrete filled steel tubular column and steel beam

QianYi Song,Wenda Wang,GuiQiang Hao

2009-01-01

Abstract:Concrete filled steel tubular (CFST) structure is widely used in various structures based on its favorable mechanical performance. A super high-rise building adopted the mixed structure with CFST frame and RC core wall. To satisfy the architectural need, the CFST diagonal columns between the middle two floors were used to reduce the floor plane, and a special connection was made to connect different CFST diagonal columns and steel beams. A three dimension finite element modeling (FEM) was developed to analysis the performance of this type of joints. On condition of certain typical design loading the mechanical behavior of the joints was calculated, and the whole load versus deformation curves were presented. The strength, deformation and typical failure modes of this type of joints were discussed, and some configuration methods were proposed. The result is reference to design and practice for the joints.
Nonlinear Finite Element Analysis of Multi-Story Concrete-Filled Steel Tubular Frame Based on Three-Dimension Element

FU Bo-xiao,WANG Wen-da,ZHANG Peng-peng

DOI: https://doi.org/10.3969/j.issn.2095-0985.2011.03.028

2011-01-01

Journal of Civil Engineering and Management

Abstract:The steels and concrete can express their characteristics adequately in apply of concrete-filled steel tube(CFST) structures which have been used to the pract ical engineering widely.Basing on the elastic-plasticity theory,the software A BAQUS was used to do a three-dimension finite element numerical simulation to a multi-story CFST frame structure.The material and geometric nonlinear were co nsidered,and the load versus displacements(P-Δ) relation of the CFST fra me was analyzed under monotonic loading.Some critical issues,such as the const itutive model of core concrete and steel,interface model of steel tube and conc rete,were discussed.Numerical simulation and experimental results show good ag reement.
Experimental and Numerical Research on the Uniaxial Behavior of the Stiffened Circular Concrete-Filled Steel Tube Stub Columns

Ming Zheng,Xin Nie,Ran Ding

DOI: https://doi.org/10.1016/j.engstruct.2024.117785

IF: 5.582

2024-01-01

Engineering Structures

Abstract:In large-span bridges or high-rise buildings, CFST columns with large width-to-thickness ratio are often adopted, which require proper stiffening measures to improve the mechanical behaviors. This paper presents a comparative study of circular CFST stub columns with different stiffening methods, including longitudinal stiffeners (cross-shaped, T-shaped and ordinary type), additional reinforcement and headed studs. Axial compression tests have been conducted to investigate the effects of different stiffening methods on the failure mode, ultimate strength and ductility of the circular CFST stub columns. Finite element models are established to simulate the columns’ behaviors and conduct parametric studies. Based on test and simulation results, an axial bearing capacity prediction model for circular CFST stub columns stiffened by longitudinal stiffeners is proposed. It is demonstrated that the failure modes of the steel tube and core concrete are changed by the longitudinal stiffeners. The longitudinal steel stiffeners as well as reinforcing cage can effectively improve the axial bearing capacity and ductility of the columns. The latter is more efficient in promoting the bearing capacity while the former is more efficient in improving the ductility and residual strength. A combination of the additional stirrups and the ordinary stiffeners will be a more economical choice. In addition, the proposed formula gives better prediction accuracy compared to the equations in various design codes.
EXPERIMENTAL RESEARCH AND NONLINEAR FINITE ELEMENT ANALYSIS ON NEW TYPE JOINT BETWEEN COLUMN AND STEEL BEAM OF CONCRETE-FILLED RECTANGULAR STEEL TUBULAR

Xu Yu,Jinming Zai,Weiqing Liu

DOI: https://doi.org/10.3969/j.issn.1005-1120.2009.01.011

2009-01-01

Abstract:Experimental results of new type joints between the column and the steel beam of concrete-filled rectangular steel tubular (CFRT) under reversed cyclic loads are presented. The earthquake resistant capacity of the joint is influenced by infilled concrete, stiffener length and relative dimensions of column and beam. It is found that the hysteresis curves obtained in the experiment are full and the joints have a good energy dissipation capacity. The nonlinear finite element models are also used to analyze the hysteresis behavior of the joints under reversed cyclic loads using ANSYS 8.0. The influences of the stiffener length and the infilled concrete are analyzed. Analytical results show that the stiffener length and the infilled concrete are critical for the joints. Furthermore, the skeleton curves of the finite element models are in good agreement with those of experiments.
Experimental Study On Concrete Filled Circular Steel Tubular Column To Steel Beam Composite Frames

Wen-Da Wang,Lin-Hai Han,Xiao-Ling Zhao

2008-01-01

Abstract:This paper describes six composite frame tests carried out on steel beam to concrete filled steel tubular (CFST) circular columns using external ring. The frame specimens were tested under a constant axial load and a cyclically increasing lateral load. Each test frame specimen consisted of two CFST columns and a steel beam segments to represent an interior frame in a building. The main test parameters included the axial load level and the beam to column linear stiffness ratio. This paper presents an analysis of the experimental results to evaluate the influences of different testing parameters on various characteristics of the composite frame performance. The test results show that the lateral load versus lateral displacement hysteretic curves of the composite frame were plump shuttle shape. The curves have no obvious strength deterioration and stiffness degradation. It was found that the composite frames exhibited high levels of energy dissipation and ductility. The initial lateral rigidity and the equivalent damping coefficient of the frame was almost unchanged within the current limitation of axial load level. The axial load level of columns have a evident effect for the strength and seismic performance of the frames, and with increase of axial load level of columns, the lateral ultimate strength of the frames become low, and the ductility and the capacity of energy dissipation also become descending.
Nonlinear FEM Analysis of Steel Beam-to-Concrete Filled Steel Square Tube Column Connections with External Stiffening Rings

WANG Jingfeng,HAN Linhai,JIANG Ying

DOI: https://doi.org/10.3969/j.issn.2095-1922.2007.02.001

2007-01-01

Abstract:To study the effects of width of stiffening ring and axial load level of the column on the behavior of beam-to-column connections,nonlinear finite element method(FEM) analysis on steel beam-to-concrete filled steel tube(CFST) column connections with external stiffening rings was carried out by ABAQUS software.Determination methods for the constitutive models of steel and concrete,interface model between the steel tubes and the core concrete were presented.The lateral load(P) versus lateral displacement(⊿) envelope curves were analyzed and validated by the experimental results.Reasonable design of width of stiffening ring was proposed.The results showed that load-bearing capacities of connections decreased with a reducing of width of stiffening ring or an increasing of axial load level.In addition,the load-bearing capacities of CFST connections with 2/3 times width of stiffening ring designed by present specifications can satisfy their requirement of strength and stiffness for earthquake-resistance.
Shear Bearing Capacity of Framework Joints of Steel-Reinforced Concrete-Filled Circular Steel Tube

Yongjun Lin,Kaiqi Liu,Tianxu Xiao,Chang Zhou

DOI: https://doi.org/10.1155/2020/7324865

IF: 2.0981

2020-01-16

Advances in Materials Science and Engineering

Abstract:In this paper, in order to investigate the shear mechanism and shear capacity of framework joints of steel-reinforced concrete-filled circular steel tube (SRCFCST), a numerical finite element model reflecting the mechanical behavior of framework joints of SRCFCST column-reinforced concrete beam is established through simulating concrete by the damage plastic constitutive model and simulating steel by the ideal elastic-plastic material, and its effectiveness is verified by experimental data. On account of uniform distribution of circular steel reinforced around the section and without definite flange and web, the shear mechanism of the framework joints of SRCFCST is analyzed on the basis of equivalent circular steel tube (CST) to the rectangular steel tube. The method for calculating the superposed shear bearing capacities of the joint core area is proposed, which is composed of four parts, i.e., concrete inside tube, concrete outside tube, hooping and steel-reinforced web; and the corresponding formulas for calculating shear bearing capacity are established. The comparative analysis of joints’ shear bearing capacity indicates that the results of numerical simulation and shear bearing capacity formulas coincide well with the experimental values, which can provide reference for the nonlinear analysis and engineering design of similar joints.

materials science, multidisciplinary
Experimental study on seismic behaviors of prefabricated embedded concrete-filled steel tube special-shaped column exterior frame

Xueyuan Guo,Liwei Wu,Haibin Chen,Shuai Wang

DOI: https://doi.org/10.1080/19648189.2022.2130994

2022-12-10

European Journal of Environmental and Civil engineering

Abstract:The new type of prefabricated embedded concrete-filled steel tube (CFST) special-shaped column structure delivers green and environmentally-friendly strengths and high space. In this study, a full-scale frame test piece with one frame façade, two stories and two spans are designed and fabricated for purposes of exploring the seismic performance and node connection safety of filled built-in steel tube concrete-filled special-shaped column, and low cyclic load testing is implemented. The bearing characteristics, deformation capacity, energy-dissipating capacity, ductility and stiffness degradation of the test piece are analyzed. The results showed that the failure mechanism is typical beam hinge mechanism. The fabricated beam-column and column-column connection nodes in this paper are safe and reliable. The hysteretic curve of fabricated embedded CFST special-shaped column is full, the ductility and energy dissipation capacity of fabricated embedded CFST special-shaped column are better than such indexes of ordinary reinforced concrete special-shaped column. The inter-story displacement angle is 1/32 when the test piece is damaged, being significantly higher than the limit value of elastic-plastic inter-story displacement angle of 1/50 under strong earthquake. The precast embedded steel-reinforced concrete special-shaped column structure is only required to be connected with steel ribs to significantly improve the construction speed and quality, delivering great economy.

engineering, civil, geological
ANALYSIS MODEL OF STEEL-TUBE CONFINED CONCRETE COLUMN AND RC BEAM FRAME CONNECTED BY RC RING BEAM

Dong-liang ZHOU,Jia-ru QIAN,Xiao-dan FANG

DOI: https://doi.org/10.3969/j.issn.1000-4750.2005.06.020

2005-01-01

Abstract:For the steel tube confined concrete (STCC) column-RC beam frame connected by reinforced concrete (RC) ring beam subjected to combined vertical and horizontal loads, there may be a very narrow gap between the ring beam and the column at certain height. The gap has influence on the frame stiffness. By finite element analysis (FEA) of the beam-column joints, the rotation stiffness and the equivalent beam width of the ring beam connector are examined, and the influence factors are investigated. It is found that the ring beam and the frame beam width have significant influence on the rotation stiffness and the equivalent width. Static and pseudo-dynamic tests on a two bay-two story STCC column-RC beam space frame with RC ring beam connectors have been performed. The test results are compared with the analysis results of a 3-bay 10-story frame. It is shown that treating the STCC column- RC beam as rigid joint is reasonable during the analysis of STCC column-RC beam frame connected by RC ring beam.
Research of circular concrete-filled steel tubular members subjected to shearing and axial compression

Wei Xian,Yanli Shi,Wenda Wang

DOI: https://doi.org/10.13614/j.cnki.11-1962/tu.2017.09.003

2017-01-01

Building Science

Abstract:Concrete-filled steel tubular (CFST) have many advantages,and they are used extensively in roadbridge project and high-rise buildings.During the period of service,the composite members may be subjected to shearing and axial compression.The study of behavior of circular CFST members subjected to shearing and axial compression is carried out using ABAQUS,and finite element model (FEM) is compared with experimental results to verify the reliability of model.The load-displacement curve,failure modes,load-distribution,stress distribution and boundary shear-span-ratio are investigated respectively.The influential parameters such as shear-span-ratio,axial-compression-ratio,ratio of steel tube,strength of steel and concrete are investigated to shearing capacity of circular CFST members.The result indicates that load-displacement curve of circular CFST members is divided into elastic stage,elastic-plastic stage and plastic stage.According to different shear-span-ratios,the failure modes of members are divided into compression-shearing,compression-bending-shearing and compression-bending.The axial-compression-ratio has a great effect on the shape of load-distribution curve.Finally,the shear-span-ratio,axial-compression-ratio,ratio of steel tube,strength of steel and concrete have some effect on shearing capacity of circular CFST members and the elastic stiffness.

Experimental Study and FE Analysis on New Frame Joints of Concrete-Filled Steel Tube Structure

Numerical Analysis of Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges

EXPERIMENTAL INVESTIGATION AND NONLINEAR FINITE ELEMENT ANALYSIS ON THE BEHAVIOR OF CONCRETE-FILLED SQUARE STEEL TUBULAR COLUMN CONNECTIONS

Finite-element Analysis for Nonlinear Stabilities of Concrete-filled Steel Tubular Arch Bridges

Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Analytical Study of Circular Concrete-Filled Steel Tube Stub Columns under Axial Compression

Study Of Mechanical Performance Of Concrete-Filled Steel Tubular Joints

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Experimental investigation of thin-walled concrete-filled steel tube columns with reinforced lattice angle

FINITE ELEMENT ANALYSIS ON CONCRETE-ENCASED CFST COLUMN TO REINFORCED CONCRETE BEAM JOINTS

Experimental study on seismic behaviors of a new type of frame joint between concrete-filled rectangular steel tubular columns and steel beams

FE modeling analysis of the joints with diagonal concrete filled steel tubular column and steel beam

Nonlinear Finite Element Analysis of Multi-Story Concrete-Filled Steel Tubular Frame Based on Three-Dimension Element

Experimental and Numerical Research on the Uniaxial Behavior of the Stiffened Circular Concrete-Filled Steel Tube Stub Columns

EXPERIMENTAL RESEARCH AND NONLINEAR FINITE ELEMENT ANALYSIS ON NEW TYPE JOINT BETWEEN COLUMN AND STEEL BEAM OF CONCRETE-FILLED RECTANGULAR STEEL TUBULAR

Experimental Study On Concrete Filled Circular Steel Tubular Column To Steel Beam Composite Frames

Nonlinear FEM Analysis of Steel Beam-to-Concrete Filled Steel Square Tube Column Connections with External Stiffening Rings

Shear Bearing Capacity of Framework Joints of Steel-Reinforced Concrete-Filled Circular Steel Tube

Experimental study on seismic behaviors of prefabricated embedded concrete-filled steel tube special-shaped column exterior frame

ANALYSIS MODEL OF STEEL-TUBE CONFINED CONCRETE COLUMN AND RC BEAM FRAME CONNECTED BY RC RING BEAM

Research of circular concrete-filled steel tubular members subjected to shearing and axial compression