Abstract:Masonry structures often exhibit poor seismic performance during earthquakes owing to their low material strength, structural integrity, and ductility. To address the mechanism of in-plane damage and collapse of masonry walls subjected to earthquake ground motion, three full-size brick walls, one with structural columns and two without structural columns, were designed and constructed in this experimental study to quantitatively investigate the effect of structural columns on the seismic performance of masonry walls. Quasi-static tests of masonry walls subjected to cyclic lateral loading were conducted using electrohydraulic servo actuators. The in-plane damage evolution and failure mode of the masonry walls under lateral loading were investigated. A numerical model with a novel plastic damage constitutive model of masonry was established. The accuracy of this model and the calculation results were verified by comparing them with the crack development and mechanical property curves obtained from the experiments. Based on the numerical model, a parametric analysis was conducted to investigate the influence of critical factors, such as mortar strength, vertical load, and height-to-width ratio, on the seismic performance of masonry structures. The test results showed that structural columns can effectively improve the performance of masonry structures. Properly installed structural columns can improve the peak load-bearing capacity, ductility, and energy dissipation of masonry structures. The masonry damage constitutive model used in this study could simulate the damage to masonry wall specimens well and reflect the hysteretic curves of the specimens within an acceptable range of accuracy. Thus, it provides a valuable reference for physical experiments. An appropriate mortar strength and vertical compressive stress can effectively enhance the load-bearing capacity of masonry structures within a certain range. For structural column walls. Walls with mortar strengths (average compressive strength) of 12.5 MPa, 10 MPa, 7.5 MPa, and 5 MPa showed an increase in peak bearing capacity of 26.2 %, 23.9 %, 18.5 %, and 9.4 %, respectively, compared to walls with mortar strengths (average compressive strength) of 2.5 Mpa. The aspect ratio had a significant impact on the shear load-bearing capacity of the masonry walls. An increase in the aspect ratio led to a transition from shear failure to flexural failure and a subsequent decrease in shear load-bearing capacity. For masonry walls with structural columns, increasing the diameter of the longitudinal steel in the structural columns can enhance the load-bearing capacity of the masonry wall, resulting in a significant improvement in its overall performance.

OUT-OF-PLANE BEHAVIOUR OF UNREINFORCED MASONRY WALLS WITH TOPOLOGICAL INTERLOCKING BRICK

Analysis of Initial Cracking of an Interface between a Bundled Lipped Channel-Concrete Composite Wall and an Infill Wall

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Seismic behavior of load-bearing horizontal-hole interlocking concrete block masonry walls: An experimental investigation of variable configurations

Influence of constructional measurements on cracking of wall with small concrete hollow blocks

Experimental Study on Lateral Resistance Behavior of Small Concrete Hollow Block Wall with Different Constructional Measures

Cyclic behavior of mortarless brick joints with different interlocking shapes

Experimental Investigation of Effect of Section Configuration on Seismic Performance of an Innovative Integrated Concrete Masonry Wall System

In-plane cyclic test on framed dry-stack masonry panel

Quasi-static, Cyclic Loading Tests of RAC Brick Masonry Walls Strengthened by Basalt Textile Reinforced Concrete

EXPERIMENTAL INVESTIGATION ON CONCRETE PERFORATED BRICK WALL SHINKAGE AT DIFFERENT AGES

In-Plane Strengthening Effect of Prefabricated Concrete Walls on Masonry Structures: Shaking Table Test

Shaking table tests and numerical simulation for brick masonry structure reinforced with polypropylene mesh cement mortar coating

Damage evolution and failure mechanism of masonry walls under in-plane cyclic loading

Experimental Investigation of Seismic Behavior of a New Type Masonry Walls

Modeling of Dry-Stacked Masonry Panel Confined by Reinforced Concrete Frame

Tie system to upgrade out‐of‐plane performance of infill masonry walls

EXPERIMENTAL STUDY ON BASIC MECHANICAL BEHAVIOR OF A NEW TYPE CONCRETE HORIZONTAL-HOLE HOLLOW BLOCK MASONRY

Study on in-plane/out-of-plane seismic performance of masonry-infilled RC frame with openings and a new type of flexible connection

Experimental Investigation on the In-Plane and Out-of-plane Interaction of Isolated Infills in RC Frames

Mechanical Performance of Prefabricated External Wall Panel under Horizontal Displacement