Abstract:The processing conditions were varied during the production of polycarbonate-based composites with the multiwalled carbon nanotubes (MWCNTs) Baytubes® C150 P (Bayer MaterialScience AG, Leverkusen, Germany), by melt mixing with an extruder on a laboratory scale. These included the screw design, rotation speed, throughput, feeding position and MWCNT content. Particular attention was paid to the shortening of the MWCNT length as a function of the conditions mentioned. It was found that there is a correlation between the applied specific mechanical energy (SME) during the melt mixing process and MWCNT dispersion, which was quantified by the agglomerate area ratio of the non-dispersed nanotubes based on optical microscopic analysis. The higher the SME value, the lower this ratio, which indicates better dispersion. Above an SME value of about 0.4 kWh/kg, no further improvement in dispersion was achieved. The MWCNT length, as measured by the quantitative analysis of TEM images of the MWCNTs dissolved from the composites, decreased with the SME value down to values of 44% of the original MWCNT length. At a constant loading of 3 wt.%, the tensile strength and tensile modulus were almost independent of the SME, while the elongation at break and notched impact strength showed an increasing trend. The variation in the feeding position showed that feeding the MWCNTs into a side feeder led to slightly better electrical and mechanical properties for both types of MWCNTs studied (Baytubes® C150 P and NanocylTM NC7000 (Nanocyl S.A., Sambreville, Belgium)). However, feeding into the hopper led to better CNT dispersion with Baytubes® C150 P, while this was the case with NanocylTM NC7000 when feeding into the side feeder. The screw profile had an influence on the dispersion, the MWCNT length and the electrical resistance, but only to a small extent. Distributive screws led to a greater shortening of the MWCNT length than dispersive screws. By varying the MWCNT content, it was shown that a greater MWCNT shortening occurred at higher loadings. Two-stage masterbatch dilution leads to stronger shortening than composite production with direct MWCNT incorporation.

Effects of MWCNTs Size on Melt Flow Properties of Polypropylene Composites During Capillary Extrusion

Melt extrudate swell behavior of multi‐walled carbon nanotubes filled‐polypropylene composites

Nanocomposites of Poly(vinylidene Fluoride) with Multiwalled Carbon Nanotubes

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Effects of MXene on Nonisothermal Crystallization Kinetics of Isotactic Polypropylene.

Multi-walled carbon nanotube reinforcement in polypropylene nanocomposites: comprehensive analysis of thermal behavior, mechanical properties, and dispersion characteristics

Thermal Properties and Thermal Stability of PP/MWCNT Composites

Effect of Multi-Walled Carbon Nanotubes on the Properties of Polyoxymethylene

Effects of Carbon Nanotubes on the Morphology and Properties of Uncompatibilized and Maleic Anhydride-grafted Polypropylene-compatibilized Polyamide 6/polypropylene Blends

DYNAMIC RHEOLOGICAL PROPERTIES OF POLYSTYRENE/MULTI-WALLED CARBON NANOTUBES COMPOSITES

STUDIES ON INFLUENCES OF VISCOELASTIC PROPERTIES ON MELT EXTRUSION OF CARBON NANOTUBES-FILLED ISOTACTIC POLYPROPYLENE COMPOSITES

Electrical Resistivity, Crystallization and Mechanical Properties of Polypropylene/Multi-Walled Carbon Nanotube/Calcium Carbonate Composites Prepared by Melt Mixing

Comparative study on the electrical, thermal, and mechanical properties of multiwalled carbon nanotubes filled polypropylene and polyamide 6 micromoldings

Mechanical and Thermal Properties Modeling, Sorption Characteristics of Multiscale (Multiwalled Carbon Nanotubes/Glass Fiber) Filler Reinforced Polypropylene Composites

Effect of Electrically Inert Particulate Filler on Electrical Resistivity of Polymer/Multi-Walled Carbon Nanotube Composites

Melt rheological properties of nylon 6/multi-walled carbon nanotube composites

Influence of a Liquid-Like MWCNT Reinforcement on Interfacial and Mechanical Properties of Carbon Fiber Filament Winding Composites

Effects of carbon nanotube length on interfacial properties of carbon fiber reinforced thermoplastic composites

Influence of Twin Screw Extrusion Conditions on MWCNT Length and Dispersion and Resulting Electrical and Mechanical Properties of Polycarbonate Composites

Effect of long-length carbon nanotubes on yield, ultimate, dynamic mechanical, and thermal properties of polyamide-6 composites prepared by twin-screw extrusion

Temperature and shear dependence of rheological behavior for thermoplastic polyurethane nanocomposites with carbon nanofillers