Abstract:The hot deformation behaviors of Fe–28Mn–10Al–1.5C–0.6V steel at T = 950–1150 °C and = 0.01–10 s −1 were studied using the Gleeble-3500 thermo-mechanical simulator. The constitutive model of Fe–28Mn–10Al–1.5C–0.6V steel was established by an artificial neural network (ANN) based on the experimental flow stress data. The critical conditions of dynamic recrystallization (DRX) of the steel under experimental conditions were studied by using both the Najafizadeh–Jonas work hardening rate model and the Cingara–McQueen rheological stress model. The true stress–true strain curve of the steel was analyzed, the work hardening rate was calculated, and the critical strain model was established. At the same time, the relevant material parameters were calculated by linear regression, and the DRX kinetics model of JMAK was also established. This model then was combined with the finite element software DEFORM-3D to simulate the DRX behavior of the steel during hot deformation. These results indicated that the rheological stress of Fe–28Mn–10Al–1.5C–0.6V steel at low shows higher temperature sensitivity and that high T and low are conducive to the occurrence of DRX. The average relative error of the ANN constitutive model is 2.40%, which has high prediction accuracy. The dynamic recrystallization conditions determined by the above models are reliable and conform to the experimental rules. By verifying the microstructure of the steel after thermal compression, the prediction error of the finite element model to the DRX volume fraction is mostly within 10%. Thus, the model has a good predictive ability and provides an effective tool for predicting plastic deformation and microstructure in industrial production.

Dynamic Recrystallization Behavior and Constitutive Modeling of As-Cast 30cr2ni4mov Steel Based on Flow Curves

Modeling of Dynamic Recrystallization Kinetics of a High Strength Low Alloy Steel During Hot Rolling

Evolution of austenite dislocation density during hot deformation using a physical dynamic recrystallization model

Determination of Recrystallization Kinetics Model of 30cr2ni4mov Steel Based on Dislocation Density

Constitutive Analysis on High-Temperature Flow Behavior of 3Cr-1Si-1ni Ultra-High Strength Steel for Modeling of Flow Stress

Research on Dynamic Recrystallization Behavior of 30Cr2Ni4MoV Rotor Steel

Dynamic Recrystallization Behavior and Processing Map Development of 25crmo4 Mirror Plate Steel During Hot Deformation

Research on hot deformation, dynamic recrystallization and numerical simulation of Fe–28Mn–10Al–1.5C–0.6V steel

Microstructure simulation and experiment investigation of dynamic recrystallization for ultra high strength steel during hot forging

Constitutive modeling and analysis on high-temperature flow behavior of 25 steel

Modeling of Dynamic Recrystallization Evolution for Cr8 Alloy Steel and Its Application in FEM

Modeling of Dynamic Recrystallization and Flow Stress of Nb‐Bearing Steels

Dynamic Recrystallization Critical Conditions and a Physically–Based Constitutive Model of Al–4.8Mg Alloy Under Hot Working Conditions

Evolution of Dynamic Recrystallization in 5CrNiMoV Steel during Hot Forming

Constitutive Modeling and Dynamic Recrystallization Mechanisms of an Ultralow-carbon Microalloyed Steel During Hot Compression Tests

Kinetics and microstructure evolution of dynamic recrystallization of medium-Mn steel during hot working

Modelling Dynamic Recrystallization of A356 Aluminum Alloy during Hot Deformation

An improved cellular automaton model of dynamic recrystallization and the constitutive model coupled with dynamic recrystallization kinetics for microalloyed high strength steels

Study on dynamic recrystallization behavior of 1MnCrMoNi steel during hot compression deformation

Hot Deformation Behavior and a Two-Stage Constitutive Model of 20mn5 Solid Steel Ingot During Hot Compression.

Study on dynamic recrystallization of ultra-high strength 22MnB5 steel during hot rolling