Abstract:To ensure the high-temperature stability of a bondline under next-generation power devices such as SiC semiconductors, a die bonding test was performed by transient liquid-phase (TLP) sinter-bonding using a Sn-coated Cu (Cu@Sn) particle-based preform. Compared to the existing 20 min-bonding result using a 30 μm Cu@Sn particle-based preform, a 5 μm Cu@Sn particle-based preform was used to significantly reduce the bonding time to 5 min, and the optimal levels of the amount of Sn in the Cu@Sn particles, the thicknesses of Sn surface finish layers on the chip and substrate, and compression pressure during the bonding were investigated. The Sn content in the Cu@Sn particles significantly changed the microstructure, including the porosity of the prepared preform. The preform porosity of 0.01% was confirmed after the formation of sufficient Sn shells with an average thickness of about 602 nm at Sn 30 wt%. In addition, in the preform with Sn 30 wt% content, the Sn phase was almost depleted after 3 min after annealing at 250 °C. The Sn finish layer was evaluated in the thickness range of 0.63−4.12 μm, and it was observed that the shear strength of the formed bondline tended to increase with increasing pressure for all Sn layer thicknesses. In particular, when the bonding was carried out at a pressure of 2 MPa using a dummy Cu chip and substrate coated with a 1.53 μm thick Sn layer, the best shear strength value of 36.89 MPa was achieved. In this case, all the Sn phases transformed into intermetallic compound phases of Cu 6 Sn 5 and Cu 3 Sn, and all the phases formed within the bondline, including Cu, exhibited high melting-point characteristics. Therefore, it was determined that there would be no remelting of the bondline or a drastic decrease in mechanical properties in a high-temperature environment below 300 o C, as initially intended. By increasing the content of the Sn shell up to 30 wt%, it was possible to achieve a nearly full density (porosity: 0.3%) bondline structure, due to the rearrangement behavior of particles, by maintaining liquid Sn for a long time during the bonding process. In conclusion, the optimal Sn finish thickness was determined to be at the level of 1.5 μm, and the optimal pressure was at the level of 2 MPa. The short bonding time of 5 min represents a significant advance in TLP bonding processes, and it is expected to contribute to a substantial improvement in the die bonding of future SiC power devices.

Cu@Sn Core–Shell Structure Powder Preform for High-Temperature Applications Based on Transient Liquid Phase Bonding

Fabrication of cu@sn core-shell structure preform and application in high temperature bonding

Fabrication of Cu@Sn Core-Shell Structured Particles and the Application in High Remelting Temperature Bonding

Cu@Sn@Ag Core–shell Particles Preform for Power Device Packaging under Harsh Environments

Ag@Sn Core‐Shell Powder Preform with a High Re‐Melting Temperature for High‐Temperature Power Devices Packaging

Die Attach Materials with High Remelting Temperatures Created by Bonding Cu@Sn Microparticles at Lower Temperatures

Fabrication of Sn-plated Cu foam for high-efficiency transient-liquid-phase bonding

Novel transient liquid phase bonding through capillary action for high-temperature power devices packaging

Transient Liquid-Phase Sinter-Bonding Characteristics of a 5 um Cu@Sn Particle-Based Preform for High-Speed Die Bonding of Power Devices

Die-attach Bonding at 230 °C Using Micron Sn-coated Zn Particles for High-Temperature Applications

An Interconnection Method Based on Sn-coated Ni Core-Shell Powder Preforms for High-Temperature Applications

Cu–Sn and Ni–Sn transient liquid phase bonding for die-attach technology applications in high-temperature power electronics packaging

Study of Electroless Sn-coated Cu Microparticles and Their Application As a High Temperature Thermal Interface Material

A paste based on Cu@Sn@Ag particles for die attachment under ambient atmosphere in power device packaging

Ag-Sn Bimetallic Nanoparticles Paste for High Temperature Service in Power Devices

Novel Sn-Cu Based Composite Solder Preforms Capable of Low Temperature Reflow for Die Attachment of High Temperature Power Electronics and the Transient Liquid Phase Bonding Process

Facile preparation of Cu foam/Sn composite preforms for low-temperature interconnection of high-power devices

Transient Liquid Phase Bonding of Cu@Sn Core–shell Particles with Added Sn–3.0Cu–0.5Ag

Interconnection method based on Cu-foam/Sn composite preform for high-temperature applications

Solder Preforms Composed of High Cu-content Sn-xCu Alloys for Power Electronic Packaging and Characterization of the Processing Performance and Joint's Properties

Sn-Coated Cu Microparticle Paste For High Power Device Packaging