Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Biomimetic cellular-structured MCMB@WC composites with excellent mechanical properties

Biomimetic Structure-Driven High Strength and Toughness in Continuous Sic Skeleton-Reinforced Graphite Composites

Microstructure Evolution and Mechanical Properties of Bioinspired Web-Liked (tib + TiC + Ti3Si)/TC4 Composites

Exceptionally Low Ablation Rates Realized in the Cellular-Structured MCMB@WC Composites Via Biomimetic Design

Microstructure evolution and mechanical properties of bioinspired web-liked (TiB + TiC + Ti 3 Si)/TC4 composites

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Determination of Microstructure and Mechanical Properties of Ceramics Bonded Tungsten Carbide Doped with Hybrid Graphene/sicw

Microstructure and Mechanical Properties of TiC/multi-principal-component Alloy Composites with Biomimetic Micro-Laminated Structure

A novel approach to fabricate WC reinforced W Cu composites via MSC and infiltration method

Preparation of WC@graphene reinforced titanium diboride‐based composite ceramic materials fabricated via SPS

Preparation and In-Situ Strengthening Mechanisms of Mo Composites with the Addition of WC

Nacre-like carbon fiber-reinforced biomimetic ceramic composites: Fabrication, microstructure, and mechanical performance

Structural effects in 'brick-and-mortar' architecture: Bio-inspired ceramic matrix composites developed through a new method

Dual-grained Mo2FeB2-based cermets containing WC fabricated via multi-step sintering approach: Microstructure, mechanical properties and interface characteristics

Interface Modification Strategy to Construct SiC Nanowires@pyrolytic Carbon Reinforcement for Carbon Fiber Composites

Effect of WC Incorporation on the Microstructure and Mechanical Properties of Ni625/WC Spark Plasma Sintered Composites

Numerical investigations on the hybrid effect and deformation mechanism of TiB2p and TiBw reinforced Cu composites prepared by in-situ mixing casting

Hybrid Bio-Inspired Structure Based on Nacre and Woodpecker Beak for Enhanced Mechanical Performance

Fabrication and mechanical properties of in situ prepared mesocarbon microbead/carbon nanotube composites

Preparation of PEEK/MWCNTs Composites with Excellent Mechanical and Tribological Properties

Fabrication of Bamboo-Inspired Continuous Carbon Fiber-Reinforced SiC Composites Via Dual-Material Thermally Assisted Extrusion-Based 3D Printing