Abstract:To improve the mechanical properties of the rolling body surface of wind power bearings, extend its service life. In this study, a large-scale molecular/atomic parallel processor LAMMPS was introduced, and then the process of magnetron sputtering technology in the preparation of DLC/Ni-DLC thin films on the 42CrMo substrate material was simulated. The effects of deposition parameters such as sputtering temperature, sputtering voltage, deposition air pressure, and Ni doping on the residual stress, film base bonding, and organizational structure of the thin films were investigated. The simulation results show that for different deposition parameters, the atomic tensile and compressive stresses existed simultaneously in DLC/Ni-DLC films, and the residual stresses were between - 0.504-5.003 Gpa and - 2.11-0.065 Gpa, respectively; the doping of Ni effectively improved the distribution of hybrid structure and the mechanical properties of the DLC films, and the ratio of the sp3 hybrid structure in the film organization was about 2.56 times higher than that of the non-doped films, and the membrane base bonding force was increased by 32.78% and the residual stress is reduced and transitioned from tensile stress to compressive stress. In addition, it was observed that the thickness of the mixed layer of DLC/Ni-DLC films with the substrate was not increased after the thickness of the mixed layer was extended to about 2 nm. Nickel doping and reasonable control of deposition parameters help to reduce the residual stress and improve the bonding strength of the film by changing the organizational structure of the film, which provides an important theoretical and scientific basis for the preparation of low-stress, high-performance and long-life DLC films and the wide application of rolling bodies for wind power bearings under complex working conditions.

Electrodeposition and microstructure of Ni and B co-doped diamond-like carbon (Ni/B-DLC) films

Electrodeposition, microstructure and tribological performance of Ni/(N) incorporated diamond-like carbon films

Electrodeposition, microstructure, friction and electrochemical behavior of diamond-like carbon (DLC) films with Ni/Cu interlayer

Effect of PDDA‐MWCNTs concentration on the microstructure and friction behavior of Co‐doped diamond‐like carbon (Ni/N/MWCNTs‐DLC) films

Microstructure, wear and corrosion behavior of nano-CeO2 doped diamond-like carbon (DLC) composite films

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

The effects of Cr and B doping on the mechanical properties and tribological behavior of multi-layered hydrogenated diamond-like carbon films

Mechanical and tribological properties of non-hydrogenated DLC films synthesized by IBAD

Optical and structural properties of nitrogen incorporated Ni doped diamond-like carbon thin films

The Impact of Dopants (B, H) on the Mechanical Behavior and Tribological Performance of DLC Film under Water Lubrication

Ti-TiC-TiC/DLC gradient nano-composite film on a biomedical NiTi alloy.

Doping of rf plasma deposited diamond-like carbon films

Structural Characterization And Properties Enhancement Of Diamond-Like Carbon-Films Synthesized Under Low-Energy Ne+ Bombardment

Structure and Mechanical Performance of Nitrogen Doped Diamond-like Carbon Films

The Effects of Ti/Ni Doping on the Friction and Wear Properties of DLC Coatings

Diamond-like Carbon Film Synthesized by Ion Beam Assisted Deposition and Its Tribological Properties

A Comparative Study of Copper-doped and Copper, Nitrogen Co-doped DLC Film Electrode and Its Electrochemical Properties

Preparation, Characterization and Tribological Properties of Diamond-Like Carbon Film on AZ31 Magnesium Alloy

Effect of rGO concentration on the microstructure and friction behavior of co-doped diamond-like carbon (Ni/N/rGO-DLC) films

Preparation and characterization of La2O3 doped diamond-like carbon nanofilms (I): Structure analysis

Molecular dynamics simulation of hybrid structure and mechanical properties of DLC/Ni-DLC thin films