Abstract:The thermite reaction between Al and CuO is well known and highly exothermic. For a conventional thermite mixture, the reaction is rate limited by a slow heterogeneous mass transfer at the metal and oxide interface. The relatively low reaction rate and ignition difficulty have restricted practical applications for this reaction. For newly developed nanocomposed thermites, the interface area is substantially increased resulting in a much higher reaction rate and a new range of possible applications. A top-down approach to preparation of reactive nanocomposite materials in the Al-rich Al-CuO system is discussed in this paper. The materials are prepared using arrested reactive milling, a technique based on high-energy ball milling performed at room temperature and stopped (or arrested) before the exothermic reaction between Al and CuO is triggered mechanically. The products are micron-sized, fully dense powders in which reactive components are uniformly mixed on the nanoscale. Optimized milling conditions for the powders with bulk compositions xAl + 3CuO with x = 8, 10, and 12 are found. Respective powders are produced and characterized. Particle sizes are measured and the sizes of nano-inclusions of CuO in Al matrix are determined. Reactions occurring in the nanocomposite materials are also characterized by thermal analysis. Ignition of the produced powders is studied by coating them onto an electrically heated filament. Constant volume explosion experiments are used to characterize combustion performance of the produced powders. Compositions of the produced powders and products of their combustion are studied by X-ray powder diffraction. Correlations between combustion performance and material characteristics are established. Ignition for Al-rich Al-CuO nanocomposite powders was observed to occur at 850±10 K independently of the heating rate.

Preparation and characterization of modified Al/Fe2O3 nano-thermite composite system

Synthesis of Fe2O3/Al Nanocomposite and Research on Its Thermite Reaction

Study on combustion characteristics and pyrotechnic cutting effects of bimetal thermite Ni/Al/Fe2O3 system

Enhanced energy performance from core–shell structured Al@Fe2O3 nanothermite fabricated by atomic layer deposition

Research progress on nano-thermite

Mechanism for thermite reactions of aluminum/iron-oxide nanocomposites based on residue analysis

Preparation of Core-Shell Ni (cu, Co)/Al Micron-Nano Composites and Characteristics of Thermite Reactions with Fe2o3

Thermal and combustion behavior of Al-MnO2 nanothermite with poly(vinylidene fluoride -co- hexafluoropropylene) energetic binder

Effect of fluoropolymer content on thermal and combustion performance of direct writing high-solid nanothermite composite

Ball Milling Produced FeF3‐Containing Nanothermites: Investigations of Its Thermal and Inflaming Properties

Ti/CuO and Ti/CuO/Cellulose Nitrate Nanothermites: An Early Insight into Their Combustion Mechanism

Fully Dense, Aluminum-Rich Al-Cuo Nanocomposite Powders for Energetic Formulations

Hot Bridge-Wire Ignition of Nanocomposite Aluminum Thermite Synthesized Using Sol-Gel-Derived Aerogel with Tailored Properties for Enhanced Reactivity and Reduced Sensitivity

Ti/CuO Nanothermite—Study of the Combustion Process

Comparative investigations of ternary thermite Al/Fe2O3/CuO and Al/Fe2O3/Bi2O3 from pyrolytic, kinetics and combustion behaviors

Enhancing the energy release performance of nanothermites through metal oxides free oxygen and pores

Effect of Fe2O3 as an accelerator on the reaction mechanism of Al–TiO2 nanothermite system

Electrophoretic Deposition and Characterization of Highly Exothermic Al/CuO Nanothermites

Pushing the Limits of Energy Performance in Micron-Sized Thermite: Core–Shell Assembled Liquid Metal-Modified Al@Fe2O3 Thermites

High dispersity and ultralight PVP-mediated Al/MFe2O4/g-C3N4 (M = Cu, Mg, Ni) nanothermites synthesized by a novel sol-freeze-drying technology

Enhancing the Energy Release Performance of Al/CuO Nanothermites through Hierarchical Structure