Abstract:Laser Powder Bed Fusion (LPBF) presents novel opportunities for the processing and manufacturing of magnesium (Mg) alloys. However, Mg alloys consistently face challenges with poor corrosion resistance. Consequently, it becomes imperative to delve into the corrosion behavior and mechanisms of Mg alloys formed through LPBF. This paper investigated the electrochemical corrosion behavior, the distribution of corrosion products, and the corrosion mechanism of LPBF ZK60 Mg alloy. The results show that the corrosion current density (I corr ) value of LPBF ZK60 Mg alloy is 3.76 μA∙cm -2 . The hydrogen evolution in Hank's solution steadily increases with immersion time and reaches a stable state after 24h. The corrosion rates calculated based on hydrogen evolution and weight loss are 2.1 mm/y and 2.4 mm/y, respectively. The corrosion resistance of LPBF ZK60 Mg alloy is predominantly affected by three factors: uneven microstructure, internal crack defects, and precipitate phases. The melt pool boundary is identified as a corrosion-vulnerable zone, which extends into the columnar crystal zone after corrosion. Crevice corrosion occurs at microcracks, and the precipitate phases within the grains and matrix induces galvanic corrosion. These findings suggest that the corrosion resistance of LPBF ZK60 Mg alloy may be regulated through targeted measures, such as eliminating cracks, achieving microstructure homogenization, and controlling the precipitate phases (including quantity, composition, and distribution).

Anisotropic response in corrosion behavior of laser powder bed fusion Al-Mn-Mg-Sc-Zr alloy

Study on Corrosion Characteristics and Mechanism of Laser Powder Bed Fusion of Mg-Zn-Zr Alloy

Anisotropic corrosion behavior of Sc and Zr modified Al-Mg alloy produced by selective laser melting

Corrosion Behaviour of Laser Powder Bed Fused Bulk Pure Magnesium in Hank's Solution

Densification, Microstructure and Anisotropic Corrosion Behavior of Al-Mg-Mn-Sc-Er-Zr Alloy Processed by Selective Laser Melting

Influence of heat treatment on corrosion behavior of Al–Mn–Mg–Sc–Zr alloy produced by laser powder bed fusion

Novel isotropic mechanical properties of laser powder-bed fusion Sc/Zr modified Al alloy

Investigation on mechanical properties and corrosion behavior of laser powder bed fusion 70/30 copper-nickel alloy

Distinction of Corrosion Resistance of Selective Laser Melted Al-12Si Alloy on Different Planes

Electrochemical Behavior of Laser Powder Bed Fusion (L-PBF) Ti–6Al–4V Alloy: Influence of Phase and Grain Boundaries on Surface Passive Film Formation

Anisotropic tensile creep behavior in laser powder bed fusion manufactured Al–Mn–Mg–Sc–Zr alloy

Effect of grain size and crystal orientation on the corrosion behavior of as-extruded Mg-6Gd-2Y-0.2Zr alloy

Microstructure and Corrosion Behavior of Y-modified ZK60 Mg Alloy Prepared by Laser Powder Bed Fusion

Microstructure and Corrosion Behavior of Laser-Welded Al–Mn–Zr Alloy for Heat Exchanger

Tuning the mechanical and corrosion properties of Al-Mg-Sc-Zr alloy processed by laser powder bed fusion through heat treatment

Study on the Microstructure and Corrosion Behavior of Dissimilar Aluminum Alloy Welded Joints Formed Using Laser Welding

Investigation of Grain Boundary Segregation Evolution and Corrosion Behavior in 7050 Aluminum Alloy under Oscillating Laser Melting

Wear and corrosion of an additively-manufactured AlMgScZrMn alloy

Insight on Interfacial Microstructure and Corrosion Characteristics of Mg/Al Explosive Welded Composite Plates

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

Study on the Effect of Remelt Scanning and Heat Treatment Processes on the Structure and Properties of Laser Powder Bed Fusion Formed Al-Mg-Sc-Zr Alloys