Abstract:The interface morphology of the bonding layer has a considerable effect on the damage and failure of sandwich-structured thermal barrier coatings. This work investigated the comprehensive effects of a grooved texture produced using laser ablation on the local surface strain, interfacial stress and strain, and crack behavior of the bonding layer in a thermal barrier coating system. The distribution and evolution of the local surface strain was obtained using the digital image correlation method. The interfacial stress, and the strain between the ceramic and bonding layers, were determined through a simulation of the plane-strain model, and the morphology and propagation of cracks were observed in thermal barrier coatings under an external tensile load. The results indicated that the local surface strain of the thermal barrier coating increased with the texturization of the bonding layer, whereas the fluctuation decreased. There were two inflection points in the local surface strain–time curves, corresponding to the initiation of surface cracks and that of interfacial transverse cracks. The surface cracks were initiated earlier than those without the texturization of the bonding layer. However, the behavior of the interfacial cracks was more complicated. If the roughness of the texture, defined as Rc, was small, the surface cracks propagated vertically to the interface between the ceramic and bonding layers, and turned into transverse cracks, leading to a separation of the ceramic layer. If Rc was greater than 22 μm, the surface cracks went further down to the interface between the bonding layer and substrate, and propagated horizontally, resulting in the separation of both the ceramic and bonding layers. Meanwhile, interfacial cracking and separation were deferred. A large roughness resulted in good cohesion between the ceramic and bonding layers, and a high stiffness for the coating, which improved the damage resistance and extended the life of the coating.

Microtexture Analysis of the Alumina Scale in Thermal Barrier Coatings

Different Growth Mechanisms of Alumina on the Surface of NiPtAl and MCrAlY Bondcoatings in EB-PVD TBC System

Influence factors of high temperature oxidation for Pt-modified-aluminide bond coatings

Microtexture of the thermally grown alumina in commercial thermal barrier coatings

Microstructure characteristics and deformation-induced crystalline-to-amorphous phase transformation in thermal barrier coatings during thermal cycling

Microstructure Parameters Affecting Interfacial Adhesion of Thermal Barrier Coatings by the EB-PVD Method

Microstructure and Thermal Cycling Behavior of Thermal Barrier Coating on Near-Α Titanium Alloy

Microstructure Analysis of Initial Alumina of Pt-Modified Aluminide Coatings on Ni-Based Alloy

High Temperature Hardness and Thermal Analysis of CoNiCrAlY Alloys Used As Bond Coats for Thermal Barrier Coatings

Critical Scale Grain Size for Optimal Lifetime of TBCs

Study of Failure of EB-PVD Thermal Barrier Coating Upon Near-Α Titanium Alloy

A Diffusion-Coupled Cohesive Element Model for Cracking Analysis of Thermal Barrier Coatings

Microstructure evolution of thermally grown Al2O3 on NiCrAlY bonding coating for high-temperature thin-film sensors

High Temperature In-Situ Synchrotron X-Ray Diffraction Technique of Thermal Barrier Coatings under Thermal Gradient and Mechanical Loads

Thermal Cycling Behavior of Thermal Barrier Coatings with MCrAlY Bond Coat Irradiated by High-Current Pulsed Electron Beam

Effect of Tensile Load on High Temperature Oxidation of CoNiCrAlY Coating

Thermal shock behaviors and failure mechanisms of EB-PVD thermal barrier coatings using radiant heating

Microstructure Observation and Nanoindentation Size Effect Characterization for Micron-/Nano-Grain TBCs

On crack evolution with texturization of bonding layer in thermal barrier coating

The Microstructural Investigation of Vermiculite-Infiltrated Electron Beam Physical Vapor Deposition Thermal Barrier Coatings

Effect of Thermal Growth Oxide Composition and Morphology on Local Stresses in Thermal Barrier Coatings