Abstract:To combine the advantages of ductile fillers and composite fillers and alleviate residual stress in joints between ZrB2-SiC ceramics (ZS) and TC4-TiBw composites, a novel multi-layered joint architecture composed of a layer of clustering SiC at the center of the joint (L-C-SiC) and two ductile layers without SiC particles bordering both substrates (L-DS) was designed. To achieve this, SiC particle skeletons with continuous micro-channels (SSCC) were integrated with AgCu filler as an interlayer. The effects of SSCC porosity and brazing temperature on joint microstructure and mechanical properties were investigated. In particular, the braze/ZS and braze/SSCC interfaces were analyzed through X-ray diffractometry (XRD), transmission electron microscopy (TEM), and wavelength-dispersive spectroscopy (WDS). The residual stress was also evaluated. The results indicate that increasing the brazing temperate improved the infiltration into the SSCC and promoted the SSCC/braze interface reaction (was detrimental to the SiC particle skeleton). Reducing the SSCC porosity changed the thicknesses of the two L-DSs and enhanced the inhomogeneity of the SSCC/braze interface reaction (induced a shear stress in L-C-SiC). For brazing with an interlayer of 30% porosity at 820 °C, the joint shear strength reached a maximum of ~41.2 MPa, mainly due to the construction of the multi-layered joint architecture.

The Effect of the Stirring with a Large Size of Stirrer on Formation of the Composite Joint Reinforced with SiC Particle

Study on Stirring Brazing of SiCp/A356 Composites with the Zn27Al Filler Alloy in Air

Research on Semi-Solid Stirring Brazing of SiCp/A356 Composites in Air

Semi-Solid Stirring Brazing of SiCp/A356 Composites and Aluminum Alloy in Air

Vibration assisted brazing of SiCp/A356 composites: Microstructure and mechanical behaviour

Effect of Holding Time on Microstructure and Mechanical Properties of SiC/SiC Joints Brazed by Ag-Cu-Ti + B4C Composite Filler

Ultrasonically Aided Brazing of SiCp/A356 Composites

Ultrasonic Dissolution of Brazing of 55% SiCp/A356 Composites

Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al–6.8Mg Composites Fabricated by Semi-Solid Stirring Technique

Effect of Brazing Parameters on the Microstructure and Properties of SiC Ceramic Joint with Zr-Cu Filler Metal

Microstructure and Mechanical Properties of the SiC/Nb Joint Brazed Using AgCuTi + B4C Composite Filler Metal

Design of Multi-Layered Architecture in Dissimilar Ceramic/metal Joints with Reinforcements Clustering Away from Both Substrates

A Study of the SiCf/SiC Composite/ni-Based Superalloy Dissimilar Joint Brazed with a Composite Filler

Study of Sicp/Az61 Composites

Strengthening Mechanism of Ceramic Particle Reinforced Bonds by Ultrasonic Brazing of AlMMCs

Interfacial Microstructure and Mechanical Properties of SiC Joints Achieved by Reactive Air Brazing Using Ag-V2O5 Filler

Study of Brazeability of Sicp/A356 Composites and Aluminum Alloy Using Semisolid Metal with High Solid Fraction by Stirring

Brazing SiC Ceramic Using Novel B4C Reinforced Ag–Cu–Ti Composite Filler

Microstructure and Shear Strength of SiC Joint Brazed with LiAlSiO4 Reinforced AgCuTi Composite Filler

Effects of Stirring Parameters on Microstructure and Tensile Properties of (abow+sicp)/6061al Composites Fabricated by Semi-Solid Stirring Technique

Stir casting process for manufacture of Al–SiC composites