Abstract:An innovative method so-called ultrasonic-assisted semisolid stirring was proposed to fabricate semisolid slurries of the nano-sized SiC/7075 aluminum matrix composite. In this method, ultrasonic treatment and semisolid stirring were combined together to disperse the nano-sized SiC and break the primary dendrites of the matrix. The microstructure and mechanical properties of the semisolid slurries and rheoformed cylinder component were investigated. The results show that ultrasonic treatment dispersed the nano-sized SiC particles well due to the effect of transient cavitation and acoustic streaming. With increase of the stirring time the amount of the spheroidal grains of semisolid slurries increases, indicating achieving a better semisolid slurry. When stirring temperature is 620°C, the 20min stirring time led to a desirable semisolid microstructure consisting of a large number of spheroidal grains surrounded by liquid phase. High-quality semisolid slurries were only achieved at the stirring temperatures of 615°C and 620°C upon the 20min stirring time. Liquid fraction in the regions near to lateral surface is larger than those in the top, bottom and central regions due to main dependence on liquid flow and flow of liquid incorporating solid grains. Yield strength and ultimate tensile strength of rheoformed cylinder components of the nano-sized SiC/7075 aluminum matrix composite increased as compared with those of the 7075 matrix. Yield strength, ultimate tensile strength and elongation of the rheoformed cylinder components of the nano-sized SiC/7075 aluminum matrix composite without T6 are 264MPa, 357MPa and elongation of 7.5%, respectively. T6 heat treatment led to a significant improvement of yield strength, ultimate tensile strength and elongation. The mechanical properties of the rheoformed cylinder components with T6 of the nano-sized SiC/7075 aluminum matrix composite involve yield strength of 381MPa, ultimate tensile strength of 478MPa and elongation of 8.5%.

Effects of Stirring Parameters on Microstructure and Tensile Properties of (abow+sicp)/6061al Composites Fabricated by Semi-Solid Stirring Technique

Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al–6.8Mg Composites Fabricated by Semi-Solid Stirring Technique

Fabrication and Characteristics of (abow Plus Sicp)/6061al Composite by Semi-Solid Mechanical Stirring Technique

Study of Sicp/Az61 Composites

Effects of Whisker Surface Treatment on Microstructure and Properties of Al 18 B 4 O 33w /6061al Composites

Effect of Ultrasonic Stirring on the Microstructure and Mechanical Properties of in Situ Mg2Si/Al Composite

Effect of Ti Content and Stirring Time on Microstructure and Mechanical Behavior of Al-B4C Composites

Effects of Stirring Time and Extrusion on Microstructures and Mechanical Properties of SiC Reinforced Pure Al Matrix Composites

Effects of Mg Content on Microstructure and Mechanical Properties of SiCp/Al-Mg Composites Fabricated by Semi-Solid Stirring Technique

Effect of Mechanical Stirring on Microstructures and Properties of Semi-solid ZA27 Alloy

Microstructure and Mechanical Properties of the Semisolid Slurries and Rheoformed Component of Nano-Sized SiC/7075 Aluminum Matrix Composite Prepared by Ultrasonic-Assisted Semisolid Stirring

Optimization of process variables and characterization of mechanically agitated ceramic‐microsphere reinforced aluminium composite

Processing and Mechanical Properties of Sic Particulate Reinforced Az91 Composites Fabricated by Stir Casting

Effect of Ultrasound Field on Interfacial Bonding and Tensile Properties of SiC P/7085 Composites

Microstructures and Tensile Properties of Al–Cu Matrix Composites Reinforced with Nano-Sized SiCp Fabricated by Semisolid Stirring Process

Processing, Microstructure and Mechanical Properties of Magnesium Matrix Nanocomposites Fabricated by Semisolid Stirring Assisted Ultrasonic Vibration

Microstructure and Mechanical Properties of Sn-Bi Alloy Treated in the Semi-Solid State by Mechanical Stirring Process

Microstructures, Interface Structure and Room Temperature Tensile Properties of Magnesium Materials Reinforced by High Content Submicron SiCp

Effects of Ultrasonic Stirring on Microstructures of Al 7wt%Si Alloy Ingot

Microstructure, Properties, and Numerical Simulation of Semi-Solid Aluminum Alloy under Planetary Stirring Process

Processing, Microstructure and Mechanical Properties of Micro-Sic Particles Reinforced Magnesium Matrix Composites Fabricated by Stir Casting Assisted by Ultrasonic Treatment Processing