Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

Influence of High Temperature Processing on the Substructure of Laser Shock Processed Titanium Alloy

The Heat Treatment Influence on the Microstructure and Hardness of TC4 Titanium Alloy Manufactured via Selective Laser Melting

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Laser shock processing of titanium alloys: a critical review on the microstructure evolution and enhanced engineering performance

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy

Microstructure and High-Temperature Tribological Properties of Ti–6Al–4V Alloy Treated by Laser Shock Peening

Plastic deformation behavior of titanium alloy by warm laser shock peening: Microstructure evolution and mechanical properties

The Influence of Heat Treatment Temperature on Microstructures and Mechanical Properties of Titanium Alloy Fabricated by Laser Melting Deposition

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Effect of dynamic recrystallization on texture orientation and grain refinement of Ti6Al4V titanium alloy subjected to laser shock peening

Effect of heat treatment on microstructure and mechanical properties of laser-deposited Ti65 near-alpha titanium alloy

Effect of heat treatment on the formed specimen of TC4 titanium alloy by selective laser melting variable parameter forming process

Effects of Laser Shock Peening on Microstructure and Properties of Ti–6Al–4V Titanium Alloy Fabricated via Selective Laser Melting

Surface residual stress, micro-hardness and geometry of TC6 titanium alloy thin-wall parts processed by multiple oblique laser shock peening

Investigation of Changes in the Structure of Submicrocrystalline Titanium of VT1-0 Brand under Heat Treatment and Laser Processing with Nanosecond Pulses

Microstructure Evolution Behavior of Titanium Microalloyed Steel during Heat Treatment

Effect of laser shock processing on oxidation resistance of laser additive manufactured Ti6Al4V titanium alloy

Effects of Heat Treatments on Microstructures and Mechanical Properties of Ti6Al4V Alloy Produced by Laser Solid Forming

Effects of Heat Treatment on the Microstructure Evolution and Mechanical Properties of Selective Laser Melted TC4 Titanium Alloy

Softening Behavior and Mechanism of Laser Rapid Forming Ti-6Al-4V Alloy Deformed at the High Temperature

The strengthening mechanism of a nickel-based alloy after laser shock processing at high temperatures