Abstract:As a promising new power source, the proton exchange membrane fuel cell (PEMFC) has attracted extensive attention. The PEMFC engine produces a large amount of waste heat during operation. The excessive temperature will reduce the efficiency and lifespan of PEMFC engine and even cause irreversible damage if not taken away in time. The thermal management system of the PEMFC plays a critical role in efficiency optimization, longevity and operational safety. To solve the problem of high heat production in the operation of the PEMFC, two approaches are proposed to improve the heat dissipation performance of the radiators in thermal management systems. Three kinds of nanofluids with excellent electrical and thermal conductivity–Al2O3, SiO2 and ZnO– are employed as the cooling medium. The radiator parameters are optimized to improve the heat transfer capability. A typical 1D thermal management system and an isotropic 3D porous medium model replacing the wavy fin are constructed to reveal the effects of the nanofluid and the parameters of the radiator performance and the thermal management system. The results show that all three kinds of nanofluids can effectively improve the heat transfer capacity of the coolant, among which the comprehensive performance of the Al2O3 nanofluid is best. When the mass flow rate is 0.04 kg/s and the concentration is 0.5 vol%, the amount of heat transfer of the Al2O3 nanofluid increases by 12.7% when compared with pure water. Under the same conditions, it can reduce the frontal area of the radiator by 12%. For the radiator, appropriate reduction of the fin pitch and wavy length and increase of wave amplitude can effectively improve the spread of heat. The use of fin parameters with higher heat dissipation power results in lower coolant temperatures at the inlet and outlet of the stack. The performance of the radiator is predicted by the two model-based approaches described above which provide a reliable theoretical basis for the optimization of the thermal management system and the matching of the components.

Simulation and Analysis for a Heat Recycle System on the Sidewall of Aluminum Reduction Cells

A Numerical Approach on Waste Heat Recovery through Sidewall Heat-Exchanging in an Aluminum Electrolysis Cell

Numerical Study on Heat and Ion Transport Characteristics Enables Optimal Design of Aqueous Thermocells for Low-Grade Heat Recovery

Simulation Study of Ferricyanide/Ferrocyanide Concentric Annulus Thermocell with Different Electrode Spacing and Cell Direction

Simulation, Experimentation, and Collaborative Analysis of Adjacent Heat Exchange Modules in a Vehicular Cooling System

Theoretical and Experimental Investigations on Liquid Immersion Cooling Battery Packs for Electric Vehicles Based on Analysis of Battery Heat Generation Characteristics

Influences of various aluminum accumulation sump designs on thermal stress distribution in drained aluminum reduction cell

Numerical Simulation Study on Gas Collecting System of 400 kA Grade Aluminum Electrolytic Cell

Numerical Simulations and Thermal Diagnostic of Ledge Formation in Hall–Heroult Aluminum Electrolysis Cell with a Solidification Front at the Cryolite-Metal Baths Interface for Reduction of Heat Losses

Simulation and Analysis of Magnetic Fields and Flow Fields of Metal Pad in 75 Ka Drained Style Aluminum Reduction Cell

A single-phase, non-isothermal model for PEM fuel cells

Improved CFD Modeling of the Whole-Cell Side Ledge Behavior in Aluminum Electrolysis Cell

Analysis of 3D Thermo - Electric Field Potential for 300 Ka Aluminum Electrolysis Cell Using ANSYS

Fully-Coupled Electric-Thermal-Flow Modeling and Investigation of Dynamic Thermal-Ledge Behavior in Aluminum Electrolysis Cell

Simulation and analysis of a noval thermal management system integrated with heat pipe radiators for 4680 battery module

Simulation of electrochemical-thermal behavior for a 26650 lithium iron phosphate/graphite cell

Simulation analysis of air cooling for vehicle power battery

Simulation and reduction of nonuniform capacity fading in a cylindrical battery module via reciprocating thermal design

Model-Based Performance Optimization of Thermal Management System of Proton Exchange Membrane Fuel Cell

Performance Prediction of Plate-Fin Radiator for Low Temperature Preheating System of Proton Exchange Membrane Fuel Cells Using CFD Simulation

Simulation Analysis of Heat Transfer of Power Battery