Abstract:As a cutting-edge heat-to-power technology based on electrochemical redox reactions, thermo-electrochemical cells, also named as thermocells, are gaining increasing attentions around the world due to their high Seebeck coefficient and scalability. However, the effects of key operating parameters as well as their interactions on the output performance are not fully investigated in a given thermocell system, without providing theoretical guidance for further design and optimization of thermocells. In view of these challenges, this study established a benchmark test rig of a thermocell using platinum electrodes and potassium ferri/ferrocyanide electrolytes. Based on the test bench, the effects of various operating parameters including the electrolyte concentration, electrode orientation and electrode distance are experimentally analysed under a given temperature difference across the hot and cold electrodes. Furthermore, the orthogonal experiments are designed and performed to evaluate the interaction effects of the above operating parameters on the output performance of the thermocell. The single-factor experimental results indicate that higher electrolyte concentration leads to larger Seebeck coefficient but lower power density, while an optimal electrode orientation exists to succeed the largest Seebeck coefficient and the maximum power density within the range of 0 ∼ 180°. In detail, the maximum power density at electrode orientation 135° can attain 0.217 W/m 2 , which is 734 % higher than that of electrode orientation 0°. Besides, the results of orthogonal experiments demonstrate that the order of the relative importance to the Seebeck coefficient and power density is electrode orientation > electrolyte concentration > electrode distance, and the weight of the electrode orientation and the electrolyte concentration is much higher than that of the electrode distance. It is also found that the interaction effects between any two operating parameters are very minor on the output performance of thermocells.

Simulation Study of Ferricyanide/Ferrocyanide Concentric Annulus Thermocell with Different Electrode Spacing and Cell Direction

Numerical Study on Heat and Ion Transport Characteristics Enables Optimal Design of Aqueous Thermocells for Low-Grade Heat Recovery

Experimental Investigation of a U-tube Thermocell under Various Fe(CN)63−/4− Concentration

Heat and mass transfer performance of ferricyanide/ferrocyanide thermocell and optimization analysis

Identification of Thermodiffusion Coefficients in an Aqueous Potassium Ferri/ferrocyanide Thermocell Using Open-Circuit Voltage Data

Numerical Modeling and Current Collection Designs for Flat-Chip Solid Oxide Fuel Cell

Synergistic improvement of Seebeck coefficient and power density of an aqueous thermocell using natural convection for low-grade heat utilization

Ultra-high Performance of Ionic Thermoelectric-Electrochemical Gel Cells for Harvesting Low Grade Heat

Measurement of Thermophysical Parameters and Thermal Modeling of 21,700 Cylindrical Battery

Numerical Simulation On Ionic Wind Heat Transfer In A Thermoelectric Cooling Sysytem

A Novel Gel Thermoelectric Chemical Cell for Harvesting Low-Grade Heat Energy

Effects of operating parameters for low-grade heat driven thermo-electrochemical cells based on orthogonal experiments

Study on the thermal interaction and heat dissipation of cylindrical Lithium-Ion Battery cells

High‐Efficiency Cryo‐Thermocells Assembled with Anisotropic Holey Graphene Aerogel Electrodes and a Eutectic Redox Electrolyte

High-efficiency thermocells driven by thermo-electrochemical processes

Simulation study of the electrothermal field in a chloride electrolysis cell with 16 electrode pairs

Self‐Assembled Asymmetric Electrodes for High‐Efficiency Thermogalvanic Cells

Simulation of electrochemical-thermal behavior for a 26650 lithium iron phosphate/graphite cell

Numerical Simulation of Cell-to-cell Performance Variation Within a Syngas-Fuelled Planar Solid Oxide Fuel Cell Stack

Reduced Order Electrochemical-thermal Modeling of Cylindrical Cells Containing Graphite-Silicon Anodes Considering Thermal Gradients and Hysteresis

Hierarchically Anisotropic Networks to Decouple Mechanical and Ionic Properties for High-Performance Quasi-Solid Thermocells