Abstract:TiCrAlN hard films based on TiN or CrN show superior properties in terms of hardness, wear resistance, and thermal stability due to the addition of alloying elements. AlCrTiN films based on AlN may have higher thermal shock properties, but the knowledge of AlCrTiN films with high Al content has been insufficient until now. In this study, two sets of AlCrTiN hard films with different Al contents of 48 at.% and 58 at.% among metal components were prepared via multi-arc ion plating so as to investigate the effect of Al content on the phase composition, hardness, and thermal shock resistance of the films. The same microstructures, morphologies, and thicknesses of the fabricated film samples were achieved by changing the combination of cathode alloy targets and adjusting the arc source current during deposition. The surface chemical composition, cross-sectional elemental distribution, microstructure, morphology, phase composition, surface hardness, film/substrate adhesion strength, and thermal shock performance of the AlCrTiN films were examined. The obtained results reveal that the two sets of AlTiCrN hard films are face-centered cubic solid solutions with a columnar fine grain structure and a preferred growth orientation of (200) crystal plane. The hardness of the AlCrTiN films can be improved up to HV2850 by properly reducing the Al content from 58 at.% to 48 at.%. Meanwhile, the film/substrate adhesion performance is strong enough in terms of critical loads greater than 200 N. Furthermore, the AlCrTiN films maintain high thermal shock resistance at 600 °C when the Al content decreases from 58 at.% to 48 at.%. The optimal composition of the AlCrTiN hard films is 25:13:15:47 (at.%), based on the consideration of hardness, adhesion, and thermal shock cycling resistance. This optimal AlCrTiN hard film can be suggested as an option for protective coatings of hot process die tools.

Formation process and cross-sectional hardness of a Cr-alloyed layer on Ti6Al4V alloy

High-temperature oxidation behavior of double glow plasma Cr-Y alloyed layers on Ti 2 AlNb alloy

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Characterisation and Oxidation Behaviour of Plasma Surface Alloyed on Γ-Tial Alloy

Phase Composition, Hardness, and Thermal Shock Properties of AlCrTiN Hard Films with High Aluminum Content

Multiple Needle Cathodes Plasma Surface Alloying of Ti6Al4V with W-Mo-C-N

Preparation and Characterization of Al11cr4 Phase by Diffusion of Al/Cr Composite Film

Al-Cr Coatings Prepared by Diffusion at Low Temperature and Its Phase Characterization

Effects of Heat Treatment on Structure Transformation of Cr/Al Composite Coatings

Process optimization and property of Ti-Al-Cr-Nb coating on titanium alloy surface by laser in-situ synthesis

Analysis on phase transformation and lamellar formation of Ti-47.5Al-3Nb-1.5/3.5Cr alloys by confocal laser scanning in-situ observation

Influence of Ti on the Microstructure and Performance of Fe-Cr Alloy Cladding Layer

Microstructure and wear resistance of TiC reinforced AlCoCrFeNi2.1 eutectic high entropy alloy layer fabricated by micro-plasma cladding

Oxidation Resistance of TiAl-Inconel625 Graded Alloying Layer

Preparation and properties of CrNiWMoCoTi gradient high entropy alloy layer by plasma surface metallurgy

High Temperature Oxidation Behaviors of Al/Cr Composite Coating on Ti2AlNb Alloy

Intrinsic surface hardening and precipitation kinetics of Al 0.3 CrFe 1.5 MnNi 0.5 multi-component alloy

The Crystal Structure, Microhardness and Thermal Stability of the Ti26Al55Zn19 Alloy

Properties of TiAlCrN coatings prepared by vacuum cathodic arc ion plating

Modification mechanism of Ti-6Al-4V alloy with pre-coated Ti-Cu-Al multilayer film treated by ion nitriding: Experiments and first-principles calculations

Fabrication Of Multilayers Coatings Of Intermetallic Compound On Micro-Crystallization Ti-6al-4v Sheet By Al-Foil Pack Aluminizing