Abstract:Al-7Si-Mg alloy castings have extensive applications in automotive industries, and the tensile properties of these alloys including yield strength, ultimate tensile strength and elongation are commonly used to judge their mechanical properties. In this work, the modified precipitation kinetics model, yield strength model and strain hardening model have been proposed to predict the tensile properties of Al-7Si-Mg alloys. The precipitation kinetics model can be used to predict the precipitate microstructure parameters including the precipitate density, size, size distribution, volume fraction, and composition and so on in these alloys, combining which with the strength model, their yield strengths can be obtained. The strain hardening model can be applied to simulate the stress-strain curves during tensile process, and the ultimate tensile strengths and elongations can be obtained by combining this model with the experimental data fitted with the expression (sigma(UTS)-sigma(Y))=m center dot sigma(Y)+n+f(T-ss). First, the evolution of precipitate microstructure parameters and yield strengths as a function of ageing time were simulated, and then their comparisons with the experimental results were performed. The possible reasons resulting in the deviations between simulated and experimental yield strengths were analyzed. The stress-strain curves during tensile process of Al-7Si-0.36Mg alloy were simulated using strain hardening model, and the influences of ageing treatment and as-cast microstructure refining scale on the parameters of dislocation storage rate, dynamic recovery rate and the stress-strain curves were analyzed. Then, the ultimate tensile strengths and elongations of Al-7Si-0.4Mg alloy aged at different temperatures were predicted which are in better agreement with the experimental results, and the influence of secondary dendrite arm spacing on tensile properties was also analyzed. Finally, the limitation of present model and the factors influencing the prediction precision of tensile properties were outlined.

Mechanical Properties and Fatigue Behavior of Age Treated Die Cast AlMg5Si2Mn Alloy

Low‐cycle Fatigue Behavior of a Newly Developed Cast Aluminum Alloy for Automotive Applications

Effect of ageing and thermal exposure on microstructure and mechanical properties of a HPDC Al–Si–Cu–Mg alloy

Mechanical Properties of Al-7si-Mg Casting Alloy under Various Aging Conditions

Effects of Adding Trace Modification Elements and Heat Treatment on the Strength and Toughness of AlSi8Cu2MgMn Alloy

Microstructure and Mechanical Properties of As-Aged Mg-Zn-Sn-Mn-Al Alloys

Microstructure and Mechanical Properties of Squeeze Cast Al-5 Mg-3Zn-1Cu-1Si Alloy along Cross Section

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Cyclic Deformation Behavior of A Heat-Treated Die-Cast Al-Mg-Si-Based Aluminum Alloy

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Modeling of Strain Hardening Behavior and Mechanical Properties of Al 7Si Mg Cast Aluminum Alloys During Tensile Process

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Microstructure and mechanical properties of Mg–4Al–4Nd–0.5Zn–0.3Mn alloy

Rotating bending fatigue behavior of high-pressure diecast AlSi10MgMn alloy based on T5 heat treatment parameters

High Cycle Fatigue Behavior and Mechanical Performance of a Novel Sand-Cast Mg-Nd-Gd Alloy: Effect of Heat Treatment

Cyclic Deformation Behavior of an Overaged High-Pressure Die-Cast Aluminum Alloy

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Microstructure and Mechanical Properties of Cast Cu-15Ni-8Sn Alloy

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

Deformation Behavior of a Newly-Developed T4-treated Al–Si Die Cast Alloy