Abstract:The melt spinning process is the most common process to produce poly(ethylene terephthalate) (PET) fibers for textile and technical applications. The process involves extruding molten polymer through a spinneret followed by a drawing process. In the conventional drawing process, there appears to be an upper limit for draw ratio somewhere in the range of 3–9. Overcoming this limitation, superdrawing-based process offers a route to produce very fine denier fibers economically from as-spun fibers of 'normal' textile deniers, and it offers a unique method for quick-response manufacturing of fibers with various finer diameters (deniers) from a single spun supply. During superdrawing, PET fibers undergo large extension without significant crystallization or increase in molecular orientation. This study is directed at understanding the limitations of processing conditions for PET superdrawing process with temperatures ranging from 90 °C to 120 °C and strain rates from 0.008 s −1 to 0.425 s −1 . Evolution of crystallinity and molecular orientation of the drawn samples are evaluated using differential scanning calorimetry (DSC) and birefringence measurements. The results indicate that superdrawing is not possible for any strain rate at or below 90 °C because of significant strain-induced crystallization. Between 90 °C and 105 °C, superdrawing occurs only when the strain rate is below a threshold value, which increases from less than 0.333 s −1 to below 0.425 s −1 as temperature increases from 105 °C to 110 °C. Results also show that between 115 °C and 120 °C, superdrawing is only possible at strain rates higher than 0.016 s −1 . Increasing temperature from 110 °C to 120 °C leads to more crystallization at low strain rates (0.001 s −1 ), and less crystallization at high strain rates (0.1 s −1 ). The change of strain rate limitation from an upper bound to a lower bound around 110 °C for superdrawing suggests a change in molecular deformation mechanism based on a combination of factors such as the temperature, entanglement dynamics, and strain rate. The study also shows that the mechanism of crystallinity development in PET undergoes a transition at drawing temperature near 113 °C and strain rate of 0.17 s −1 .

Study on the Structure and Property of Ultra-Fine Denier PET Full Drawing Yarn: Effect of Draw Ratio and Take-Up Velocity

Effect of drawing and heat‐setting process on aggregate structure of Poly(ethylene terephthalate) industrial fiber in large‐scale spinning production

The Research on the Physical Properties of Polyester Filament after Drawing Treatment

Contrast of structure and properties of PET FDY from bottle-grade and fiber-grade chips

Optimization of hot drawing process of ultra‐high molecular weight polyethylene monofilament prepared by melt spinning

Effect of strain rate and temperature on the crystallization behavior of amorphous poly(ethylene terephthalate) fibers during superdrawing

Effects of Spinning Conditions on Properties of Polyester Yarn Prepared Using an Ultra-High-Speed Melt Spinning Technique Equipped with A Steam Chamber

Structure and Performance of High Dtex PET-PBT Blending Mono Filaments

Microstructure and Mechanical Properties of Hot-Air Drawn Poly(ethylene-2,6-naphthalate) Fibers

Structure–Property Evolution of Poly(ethylene Terephthalate) Fibers in Industrialized Process under Complex Coupling of Stress and Temperature Field

Research on Spinnability of 55 Dtex/36 F Superfine Lobed PET/PA Composite DTT

Preparation of High-Modulus Poly(ethylene Terephthalate) Fibers by Vibrating Hot Drawing

Study on Structures and Properties of Ultra-Hot Drawing UHMWPE Fibers Fabricated Via Dry Spinning Method

Crystallization Behavior of Melt-Spun Poly(vinyl Alcohol) Fibers During Drawing Process

The Influence of Drawing Pressure on the Properties of Pet/Pa6 Bicomponent Spunbonded Fibers

Isothermal shrinkage kinetics of PET

Morphology and properties of PTT/PA6 drawn yarn

Crimping performance and morpho structure of PET/PTT conjugated yarn

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning

Characterization of structure and properties of dark color polyester FDY with varied linear density

Structure and Properties of Gel‐spun Ultra‐high Molecular Weight Polyethylene Fibers Obtained from Industrial Production Line