Abstract:The melt spinning process is the most common process to produce poly(ethylene terephthalate) (PET) fibers for textile and technical applications. The process involves extruding molten polymer through a spinneret followed by a drawing process. In the conventional drawing process, there appears to be an upper limit for draw ratio somewhere in the range of 3–9. Overcoming this limitation, superdrawing-based process offers a route to produce very fine denier fibers economically from as-spun fibers of 'normal' textile deniers, and it offers a unique method for quick-response manufacturing of fibers with various finer diameters (deniers) from a single spun supply. During superdrawing, PET fibers undergo large extension without significant crystallization or increase in molecular orientation. This study is directed at understanding the limitations of processing conditions for PET superdrawing process with temperatures ranging from 90 °C to 120 °C and strain rates from 0.008 s −1 to 0.425 s −1 . Evolution of crystallinity and molecular orientation of the drawn samples are evaluated using differential scanning calorimetry (DSC) and birefringence measurements. The results indicate that superdrawing is not possible for any strain rate at or below 90 °C because of significant strain-induced crystallization. Between 90 °C and 105 °C, superdrawing occurs only when the strain rate is below a threshold value, which increases from less than 0.333 s −1 to below 0.425 s −1 as temperature increases from 105 °C to 110 °C. Results also show that between 115 °C and 120 °C, superdrawing is only possible at strain rates higher than 0.016 s −1 . Increasing temperature from 110 °C to 120 °C leads to more crystallization at low strain rates (0.001 s −1 ), and less crystallization at high strain rates (0.1 s −1 ). The change of strain rate limitation from an upper bound to a lower bound around 110 °C for superdrawing suggests a change in molecular deformation mechanism based on a combination of factors such as the temperature, entanglement dynamics, and strain rate. The study also shows that the mechanism of crystallinity development in PET undergoes a transition at drawing temperature near 113 °C and strain rate of 0.17 s −1 .

The Influence of Drawing Pressure on the Properties of Pet/Pa6 Bicomponent Spunbonded Fibers

Drawing and Ultimate Tensile Properties of Modified Polyamide 6 Fibers

Microstructure and Mechanical Properties of Hot-Air Drawn Poly(ethylene-2,6-naphthalate) Fibers

Effect of Drawing Parameters on the Properties of Polypropylene/Inorganic Particles Composites by Solid-State Die Drawing

Study on Structures and Properties of Ultra-Hot Drawing UHMWPE Fibers Fabricated Via Dry Spinning Method

Filtration and mechanical performance of orange petal shape bicomponent spunbond-spunlace nonwoven materials

Effect of drawing and heat‐setting process on aggregate structure of Poly(ethylene terephthalate) industrial fiber in large‐scale spinning production

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning

Preparation of High-Modulus and High-Strength Poly(Ethylene-Terephthalate) Fiber by Zone Annealing

Preparation of High-Modulus Poly(ethylene Terephthalate) Fibers by Vibrating Hot Drawing

Structure and Rheological Behavior of PET/WSPET Blend

Optimization of hot drawing process of ultra‐high molecular weight polyethylene monofilament prepared by melt spinning

Preparation of Conductive Polyester Fiber Compounded with Carbon Black

Effect of Structure on the Tribological Properties of Polytetrafluoroethylene Drawn Uniaxially at the Melting Point

Influence of processing parameters and drafting assembly design parameters on fiber diameter during spunbonding

Mechanical properties, moisture absorption, and dyeability of polyamide 5,6 fibers

Effects of needle-punched felt structure on the mechanical properties of carbon/carbon composites

Bio‐based poly(trimethylene terephthalate)/polyamide 56 blend fibers via melt spinning: Preparation, structure, and properties

Effect of strain rate and temperature on the crystallization behavior of amorphous poly(ethylene terephthalate) fibers during superdrawing

Poly(ethylene Terephthalate)/carbon Black Composite Fibers Prepared by Electrospinning

The Influence of Pressure-Induced-Flow Processing on the Morphology, Thermal and Mechanical Properties of Polypropylene Blends