Abstract:Thermal shrinkage has for long been a critical issue in nonwoven industrial applications. A dimensionally stable nonwoven web with excellent mechanical property was achieved by heat treatment with tension [taut annealed (TA)] instead of annealing under free state [free annealed (FA)], while the original high porosity was not affected. To better understand the fundamental structure-property relationship, these two different heat treatments' effects on the thermal behaviors, morphology, and phase structures of poly(phenylene sulfide) (PPS) nonwovens were elucidated via a combination of different experimental techniques such as temperature-modulated differential scanning calorimetry (DSC), two-dimensional wide-angle X-ray diffraction, two-dimensional small-angle X-ray scattering, and polarized Raman spectroscopy. It is evidenced that no obvious online stress-induced crystallization occurs during the melt-blowing process, making virgin PPS fibers mostly in the amorphous state. However, experimental results confirm that a certain amount of mesophase or constrained amorphous exists in the virgin PPS fibers without any presence of crystallites. After annealing, the DSC melting curves of both TA and FA PPS nonwovens exhibit endothermic annealing peaks, the origin of which is interpreted as the relaxation and devitrification of the rigid amorphous phase. However, the annealing peak position of the FA sample is always higher than that of the TA sample, which is reported for the first time. As compared with the FA sample annealed at the same temperature, TA PPS nonwovens reveal lower crystallinity and slightly larger lamellar long period (L-p) but a higher level of macroscopic fiber alignment and molecular chain orientation. These morphology and microstructure differences provide a good explanation for the superior mechanical property of TA PPS nonwovens with higher elastic modulus and tensile strength. The results are helpful in deepening the understanding of essential physical pictures of PPS nonwovens and promoting the development of the high-temperature nonwoven industry.

The Research on the Physical Properties of Polyester Filament after Drawing Treatment

Study on the Effect of Pre-Tension on Performance of Polyester/cotton/silk Sirofil Composite Yarn

Drawing and Ultimate Tensile Properties of Modified Polyamide 6 Fibers

Characterization of structure and properties of dark color polyester FDY with varied linear density

Optimization of hot drawing process of ultra‐high molecular weight polyethylene monofilament prepared by melt spinning

Preparation, mechanical properties and microstructure of polyoxymethylene fiber through melt spinning and hot drawing by using injection-molding grade resins

Mechanical properties, moisture absorption, and dyeability of polyamide 5,6 fibers

Effect of heat treatment on the mechanical properties of PBT/PET yarn

Microstructure and Mechanical Properties of Hot-Air Drawn Poly(ethylene-2,6-naphthalate) Fibers

Effect of Boiling and Stretching on the Optical and Mechanical Properties of Polyester Fibres

Effect of Thermal and Mechanical Processes on the Molecular Orientation of Polyester Fibres

Effect of drawing and heat‐setting process on aggregate structure of Poly(ethylene terephthalate) industrial fiber in large‐scale spinning production

Effect of fibre cross-sectional shape on the properties of POY continuous filaments yarns

The Influence of Drawing Pressure on the Properties of Pet/Pa6 Bicomponent Spunbonded Fibers

DSC Studies on the Dyeing Properties of PLA Fiber

Preparation of High-Modulus Poly(ethylene Terephthalate) Fibers by Vibrating Hot Drawing

Study on Structures and Properties of Ultra-Hot Drawing UHMWPE Fibers Fabricated Via Dry Spinning Method

Heat-setting Effect on the Morphology and Phase Structures of PPS Nonwovens

The influence of formation temperatures on the crystal structure and mechanical properties of ultrahigh-molecular-weight polyethylene/high-density polyethylene-blend fibers prepared by melt spinning

Bio‐based poly(trimethylene terephthalate)/polyamide 56 blend fibers via melt spinning: Preparation, structure, and properties

The preparation of polypropylene microfiber yarns via vortex airflow‐assisted melt differential electrospinning