Abstract:The effect of the strain rate, experimental temperature, Zn content in the test solution, and prefilming time on the mechanical properties was investigated by a tensile test with a slow strain rate, at a chemical solution of 2.2 ppm Li and 1200 ppm B in a static autoclave with 8.2 MPa. The experimental parameters clearly affected the tensile properties. The surface morphology, fractograph, and cross-sectional microstructure were analyzed by scanning electron microscopy and transmission electron microscopy. The (elongation) and UTS (ultimate tensile strength) of the samples tested in chemical solution were obviously lower than those of the samples tested under a nitrogen atmosphere. However, in general, all samples showed a ductile fracture characteristic and an excellent tensile property in all experimental conditions. The and UTS were first increased with increasing Zn content, and then decreased at both conditions of 9.26 x 10(-7)/s and 4.63 x 10(-7)/s strain rates. The difference values of tensile properties at different strain rates showed fluctuations with increasing Zn content. The increased with both increasing experimental temperature and prefilming time. The UTS first decreased with increasing prefilming time and then increased. The I-scc (stress corrosion cracking susceptibility) decreased with an increasing strain rate, experiment temperature, and prefilming time. Many particles with polyhedrons were formed on the sample surfaces, which was attributed to corrosion in a periodical location at the sample surface. The average length of the particles decreased with increasing Zn content, but increased with both increasing experimental temperatures and prefilming time. The corresponding mechanism is also discussed in this work.

Effect of Potential on Stress Corrosion Cracking of 321 Stainless Steel under Marine Environment

Effect Of Potential Perturbation Polarization On The Stress Corrosion Cracking Of Type 321 Stainless Steel

Effect of Electrochemical Potential and Chloride Concentration on Stress Corrosion Cracking Behavior of 23co14ni12cr3mo Ultra-High Strength Steel in NaCl Solution

Effect of Surface Treatment on the Stress Corrosion Cracking of 304 Austenitic Stainless Steels in Acid Chloride Solution

Effect of Applied Potentials on Stress Corrosion Cracking Susceptibility of X80 Pipeline Steel in Simulated Soil Solution

Effect of Applied Potentials on Stress Corrosion Cracking of X80 Steel in Simulated Nanxiong Soil Solution

A Study on the Propagation of Chloride-Induced Stress Corrosion Cracking for Austenitic Stainless Steel at Corrosion Environment

Effect of Potential on SCC Initiation for Pipeline Steel in Near-Neutral PH Solution

Influence of deformation-induced martensite on stress corrosion cracking of AISI 321 stainless steel

Effects of Temperature and Applied Potential on the Stress Corrosion Cracking of X80 Steel in a Xinzhou Simulated Soil Solution

Stress Corrosion Behaviors Of 316ln Stainless Steel In A Simulated Pwr Primary Water Environment

Stress Corrosion Cracking Behavior of Cold-Drawn 316 Austenitic Stainless Steels in Simulated Pwr Environment

Evaluation of the Stress Corrosion Crack Growth Behaviour of High-Strength Marine Steel Based on Model of Crack Tip Mechano-Electrochemical Effect

Stress corrosion cracking of low alloy steels and welded joints in sea water

Stress Corrosion Cracking Behavior and Mechanism of 2205 Duplex Stainless Steel under Applied Polarization Potentials

Investigation of Stress Corrosion Cracking Susceptibility of 7A52 Aluminum Alloy under Different Applied Potentials

In-Situ Electrochemical Study on Susceptibility to Stress Corrosion Cracking of New-Developed 1200 MPa Ti-35421 Titanium Alloy

Study on Stress Corrosion Property of 304 Austenitic Stainless Steel in the Environment of Acid Chloride Solution

Stress Corrosion Behavior of Diffusion Bonding Joints of 316L Stainless Steel in Environment of Acid NaCl Solution

Effect of Anions on Stress Corrosion Cracking Behaviors of Ultra-High Strength Steel 23Co14ni12cr3mo

The Effect of Applied Stress on the Crevice Corrosion of 304 Stainless Steel in 3.5 Wt% NaCl Solution