Abstract:During the cold-chamber high pressure die casting (HPDC) process, samples were produced to investigate the microstructure characteristics of AM60B magnesium alloy. Special attention was paid to the effects of process parameters on the morphology and distribution of externally solidified crystals (ESCs) in the microstructure of magnesium alloy die castings, such as slow shot phase plunger velocity, delay time of pouring and fast shot phase plunger velocity. On the basis of metallographic observation and quantitative statistics, it is concluded that a lower slow shot phase plunger velocity and a longer delay time of pouring both lead to an increment of the size and percentage of the ESCs, due to the fact that a longer holding time of the melt in the shot sleeve will cause a more severe loss of the superheat. The impingement of the melt flow on the ESCs is more intensive with a higher fast shot phase plunger velocity, in such case the ESCs reveal a more granular and roundish morphology and are dispersed throughout the cross section of the castings. Based on analysis of the filling and solidification processes of the melt during the HPDC process, reasonable explanations were proposed in terms of the nucleation, growth, remelting and fragmentation of the ESCs to interpret the effects of process parameters on the morphology and distribution of the ESCs in the microstructure of magnesium alloy die castings.

Effect of Multi-Step Slow Shot Speed on Microstructure of Vacuum Die Cast AZ91D Magnesium Alloy

Vacuum Assisted High-Pressure Die Casting of AZ91D Magnesium Alloy at Different Slow Shot Speeds

The Effect of Slow Shot Speed and Casting Pressure on the 3D Microstructure of High Pressure Die Casting AE44 Magnesium Alloy

Correlation Between Density and Microstructural Features in Vacuum Die Cast AZ91D Magnesium Alloy

Effects Of Slow, Shot Speed Of Sss Die Casting On Microstructure And Mechanical Properties Of Aluminum Alloys Adc12

Effects of Process Parameters on Morphology and Distribution of Externally Solidified Crystals in Microstructure of Magnesium Alloy Die Castings

Microstructure and mechanical properties of ADC12 aluminum alloy under super slow speed die castings with low shot speed

Influence of Melt Flow in the Gating System on Microstructure and Mechanical Properties of High Pressure Die Casting AZ91D Magnesium Alloy

Microstructural Evolution of Vacuum Die-Cast AZ91D Magnesium Alloy During Solution Treatment

Effect of Slow Shot Speed on Externally Solidified Crystal, Porosity and Tensile Property in a Newly Developed High-Pressure Die-Cast Al-Si Alloy

Analysis of Fractures and Microstructures on Different Injection Speeds in High-Pressure Die-Casting Magnesium Alloy

Fast shot speed induced microstructure and mechanical property evolution of high pressure die casting Mg-Al-Zn-RE alloys

Influence of Slow-Shot Speed on PSPs and Porosity of AlSi17Cu2.5 Alloy During High Pressure Die Casting

Influence of the Velocity and Start Position of High-Speed Injection Stage on the Quality of Magnesium Alloy Die Casting

Investigation of Properties in Magnesium Alloy Thin Plates after Die Casting Processes

Effect of Vacuum Degree on Quality of Magnesium Alloy by Low-Pressure Expendable Pattern Casting

Effects of Casting Pressure on Microstructure and Mechanical Properties of Super Slow Speed Die Castings of ADC12 Aluminum Alloy

Study on Mechanical Properties of Vacuum Die-cast AZ91D Magnesium Alloy

Effects of Ingate Speed and Dimension on Microstructure and Mechanical Properties of Super Slow Speed (SSS) Die Casting ADC12 Aluminum Alloy Castings

Characterization of A390 Aluminum Alloy Produced at Different Slow Shot Speeds Using Vacuum Assisted High Pressure Die Casting

Effects of Shot Speed and Biscuit Thickness on Externaly Solidified Crystals of High-Pressure Diet Cast Am60b Magnesium Alloy