A Two-Stage Chirped Pulse Fiber Amplifier System for Lasik

Gengji Zhou,Hongyu Yang,Tongxiao Jiang,Aimin Wang,Zhigang Zhang

DOI: https://doi.org/10.1088/1054-660x/23/4/045101

IF: 1.2

2013-01-01

Laser Physics

Abstract:We demonstrate a two-stage chirped pulse fiber amplification system which generates 50 nJ, 152 fs pulses at a repetition rate of 20 MHz.

What problem does this paper attempt to address?

Vector-dispersion Compensation and Pulse Pedestal Cancellation in a Femtosecond Nonlinear Amplification Fiber Laser System.

Chen Xie,Bowen Liu,Hailiang Niu,Youjian Song,Yi Li,Minglie Hu,Yueguang Zhang,Weidong Shen,Xu Liu,Chingyue Wang

DOI: https://doi.org/10.1364/ol.36.004149

2011-01-01

Abstract:We report on a femtosecond nonlinear amplification fiber laser system using a vector-dispersion compressor, which consists of a transmission grating pair and multipass cell based Gires-Tournois interferometer mirrors. The mirror is designed with nearly zero group-delay dispersion and large negative third-order dispersion. As a result, the third-order dispersion of the compressor can be adjusted independently to compensate the nonlinear phase shift of amplified pulses to reduce the pulse pedestal. With this scheme, the system outputs 44 fs laser pulses with little wing at 26.6W output average power and 531 nJ pulse energy, corresponding to 10.8MW peak power. (C) 2011 Optical Society of America
Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Xiang Zhang,Yi Wang,Bin Liu,Chunhua Wang,Zhen Xiang,Chong Liu

DOI: https://doi.org/10.1364/ao.53.005058

IF: 1.9

2014-01-01

Applied Optics

Abstract:A pulsed laser for laser guide stars with a 100 MHz repetition rate and 1 ns pulse width was achieved by external modulation of a continuous wave (CW) laser with a 70 kHz spectrum width. The laser is amplified first by two fiber pre-amplifiers and then by four solid-state power amplifiers. The laser achieves gains as high as 36 dB in the fiber pre-amplifiers due to the long gain medium length. The output power from the fiber amplifiers is 2.1 W. The laser receives further amplification in the solid-state amplifiers and retains good beam quality by aberration compensation. The final output average power is 102.9 W, and the beam quality factor M-2 is 1.46. The laser reaches high power without spectrum width and pulse width broadening at the 100 MHz repetition rate. The spectrum width of the pulsed laser is less than 0.8 GHz, which is close to the Fourier transform limit. Such a laser with single-frequency, high-repetition, and high-power features along with good beam quality will be valuable for many research areas. (C) 2014 Optical Society of America
Microjoule Level Femtosecond Optical Pulses with Double-Cladding Fiber-Based Nonlinear Chirped-Pulse Amplification

X. Wang,P. Li,H. Yang,T. Jiang,Y. Ma,Z. Fan,G. Niu,J. Yu,A. Wang,Z. Zhang

DOI: https://doi.org/10.1134/s1054660x11190315

IF: 1.2

2011-01-01

Laser Physics

Abstract:An all-fiber high-energy nonlinear chirped-pulse amplification system with two-stage double-cladding fiber amplifiers is presented in this paper. It generates pulses with the energy up to 10 μJ at 20 kHz repetition rate and total accumulated nonlinear phase shift as large as 12.8π. The pulses can be compressed to 137 fs with the compensation of mismatched third-order dispersion by self-phase modulation in the fiber amplifiers.
Chirped Pulse Amplified Dissipative-Soliton Erbium-doped Fiber Lasers

Junsong Peng,Li Zhan,Yu Zhang,Shouyu Luo,Xuehao Shen

DOI: https://doi.org/10.1080/09500340.2014.887151

IF: 1.3

2014-01-01

Journal of Modern Optics

Abstract:An all-fiber amplification and compression system seed is demonstrated by using a chirped pulse oscillator at the telecommunication band. Dispersion management is applied successfully both in the oscillator and amplifier, allowing dissipative soliton (DS) generation and amplification. The oscillator generates 4-ps chirped pulses with 130 mW (4.55 nJ) average power. Benefiting from large chirp and the high energy of DSs from the oscillator, the amplification system can be simplified. The average power after amplification is increased to 324.2 mW, corresponding to a single pulse energy of 11.3 nJ. The minimum pulse duration is 190 fs after the single-mode fiber (SMF) is employed to compress the pulses. The repetition rate of pulses is 28.6 MHz.
Yb-Doped Fiber Chirped Pulse Amplification System Delivering 1 mJ, 231 fs at 1 kHz Repetition Rate

Haitao Zhang,Jiaqi Zu,Decai Deng,Haozhen Xu,Junyu Chen

DOI: https://doi.org/10.3390/photonics9020067

IF: 2.536

2022-01-01

Photonics

Abstract:In this paper a single-channel chirped pulse amplification laser system based on Yb-doped photonic crystal fiber was constructed, which achieved a pulse energy output of 1 mJ with a beam quality close to the diffraction limit. Pulsed synchronous pumping was used to suppress amplified spontaneous emission at a repetition rate of 1 kHz. The de-chirped pulse width of 231 fs was achieved by precise systematic dispersion control, and the corresponding peak power reached 3.85 GW.
All-Fiber-Based Ultrashort Pulse Generation and Chirped Pulse Amplification Through Parametric Processes

Yue Zhou,Qin Li,Kim K. Y. Cheung,Sigang Yang,P. C. Chui,Kenneth K. Y. Wong

DOI: https://doi.org/10.1109/lpt.2010.2055557

IF: 2.6

2010-01-01

IEEE Photonics Technology Letters

Abstract:We experimentally demonstrate, for the first time to the best of our knowledge, the use of optical fiber for optical parametric chirped pulse amplification to amplify subpicosecond pulses. We use this system to amplify a subpicosecond signal at 1595 nm generated by a fiber-optical parametric oscillator. The 750-fs signal from the oscillator output is stretched to 40 ps, amplified by an all-fiber optical parametric amplifier and then compressed to 808 fs. The peak power of the signal is amplified from 93 mW to 10 W.
Low repetition rate broadband high energy and peak power nanosecond pulsed Yb-doped fiber amplifier

Chao Zheng,Haitao Zhang,Ping Yan,Mali Gong

DOI: https://doi.org/10.1016/j.optlastec.2013.01.011

IF: 4.939

2013-01-01

Optics & Laser Technology

Abstract:We demonstrate a broadband fiber amplifier system emitting 10nm pulses with 33mJ pulse energy at repetition rates between 1 and 20Hz. In combination with a pulse width of 10ns, a corresponding peak output power over than 3MW was achieved. This record performance was enabled by fiber with core diameter of 200μm. Furthermore, in order to suppress amplified spontaneous emission (ASE), multi-stage pulse pump technology was applied and different pumping characteristics had been measured. Finally, 15% extraction efficiency was obtained when output energy reached 33mJ. Output capability of the amplifier was not limited by SBS and ASE but the pump peak power.
Nanosecond Pulse Shaping with Fiber-Based Electro-Optical Modulators and a Double-Pass Tapered Amplifier

Charles E. Rogers III,Phillip L. Gould

DOI: https://doi.org/10.1364/OE.24.002596

2015-11-04

Abstract:We describe a system for generating frequency-chirped and amplitude-shaped pulses on time scales from sub-nanosecond to ten nanoseconds. The system starts with cw diode-laser light at 780 nm and utilizes fiber-based electro-optical phase and intensity modulators, driven by an arbitrary waveform generator, to generate the shaped pulses. These pulses are subsequently amplified to several hundred mW with a tapered amplifier in a delayed double-pass configuration. Frequency chirps up to 5 GHz in 2 ns and pulse widths as short as 0.15 ns have been realized.

Atomic Physics,Optics
Optical Parametric Chirped Pulse Amplification Based on Photonic Crystal Fibre

Wang He-Lin,Yang Ai-Jun,Leng Yu-Xin,Wang Cheng,Xu Zhi-Zhan,Hou Lan-Tian

DOI: https://doi.org/10.1088/1674-1056/20/8/084208

2011-01-01

Abstract:A compact two-stage optical parametric chirped pulse amplifier based on photonic crystal fibre is demonstrated.A 1064-nm soliton pulse is obtained in a home-made photonic crystal fibre （PCF） with femtosecond pulse pumping and then amplified to 2 mJ in an Nd:YAG regenerative amplifier.After the amplified pulses pass through the LBO crystal,the 532-nm double-frequency light with an energy of 0.8 mJ and a duration of over 100 ps at 10-Hz repetition rate is generated as a pump source in the following two-stage optical parametric amplification （OPA）.The 850-nm chirped signal light gain from the stretcher is 1.5×10 4 in the first-stage OPA while it is 120 in the second-stage OPA.The total signal gain of optical parametric chirped pulse amplification （OPCPA） can reach 1.8×10 6.
Femtosecond fiber laser for femtosecond LASIK

Yizhou Liu,Yifan Cui,Ziyun Kong,Kunlun Chen,Jian Zhang,Hang Su,Liang Hu,Hongbo Li,Shihao Chen,Zhaolun Kang,Aimin Wang,Danghui Liu,Hao Chen

DOI: https://doi.org/10.3760/CMA.J.ISSN.1674-845X.2015.07.002

2015-01-01

Abstract:Objective\r\nTo build a low repetition rate femtosecond fiber laser with its pulse width narrower than 200 fs and pulse energy bigger than 50 nJ and realize making blasting holes on pig cornea by optical expanding and focusing femtosecond laser.\r\n\r\n\r\nMethods\r\nExperimental study. Introducing very long polarization maintaining fiber into the ring cavity, the mode-locking fiber laser under the similariton amplifier scheme was used to be the oscillator. The signal laser was amplified and compressed by propagating it through the construction of pre-chirp, amplifier and de-chirp to realize outputting high quality pulse train. The high power fiber laser was expanded by the lens group. The expanded laser beam was focused into the pig cornea by the plane objective with different numerical aperture (NA) to realize making high quality blasting holes.\r\n\r\n\r\nResults\r\nThis laser facility realized outputing a very stable 19.1 MHz, 109 fs, 1.4 W, 73.2 nJ mode-locking fiber laser. After five fold expansion, the laser beam was focused into the pig cornea by the NA=0.2 plane objective to get blasting holes whose aperture were 45~75 μm. Focusing the laser beam into the pig cornea by the NA=0.5 plane objective, the aperture of the blasting holes were about 30 μm.\r\n\r\n\r\nConclusion\r\nIntroducing very long Polarization Maintaining fiber into the similariton amplifier ring cavity can improve stability effectively. The construction of pre-chirp, amplifier and de-chirp can use the nonlinear affects to depress the third order dispersion to realize high quality amplify and compression. After expanded by lens group, using higher NA plane objective to focus the expanded laser beam into the cornea can realize making higher quality blasting holes.\r\n\r\n\r\nKey words: \r\nRefractive surgical procedures; Femtosecond laser; Keratomileusis, laser in situ; Mode-locking fiber laser
Development of a Femtosecond High-Power Ytterbium-doped Fiber Laser System and Study on Spiky Spectral Modulation in Highly Nonlinear Chirped-Pulse Fiber Amplifiers

Suwon Kim,Yong-Ho Cha,Do-Young Jeong

DOI: https://doi.org/10.3938/jkps.77.1135

2020-11-19

Journal of the Korean Physical Society

Abstract:We have developed and analyzed a femtosecond high-power fiber laser system based on chirped-pulse amplification. The system consists of a homemade femtosecond ytterbium-doped fiber oscillator, a fiber pulse stretcher, a pulse picker, three ytterbium-doped fiber amplifiers and a grating-based pulse compressor. A single-mode photonic crystal fiber with a large mode-field diameter of 30 µm is used in the final amplifier, and the special homemade mode-field adapter based on a graded refractive index fiber has been developed for the photonic crystal fiber. Pedestal-free pulses of 15 µJ are generated after pulse compression at a repetition rate of 500 kHz, and the pulse width is 300 fs. When small-core-size fibers are used at the final amplifier, the generation of spiky modulations in amplified spectra is observed. We analyze the physical origin of the spiky spectral modulation and investigate the effect of the spectral modulation on the pulse shape and contrast after pulse compression by numerical simulations.

physics, multidisciplinary
Amplification of arbitrary frequency chirps of pulsed light on nanosecond timescales

B.S. Clarke,P.L. Gould

DOI: https://doi.org/10.1063/5.0076633

2021-10-28

Abstract:We have developed a system for producing amplified pulses of frequency-chirped light at 780 nm on nanosecond timescales. The system starts with tunable cw laser light and employs a pair of fiber-based phase modulators, a semiconductor optical amplifier, and a tapered amplifier to achieve chirp rates exceeding 3 GHz/10 ns and peak powers greater than 1 W. Driving the modulators with an arbitrary waveform generator enables arbitrary chirp shapes, such as two-frequency linear chirps. We overcome the optical power limitations of the modulators by duty cycling and avoid unseeded operation of the tapered amplifier by multiplexing the chirped pulses with "dummy" light from a separate diode laser.

Optics,Atomic Physics
A 12 Mj 11 Ns Spectrally Narrow Fiber Amplifier with A Pulsed Pump

Wenyong Cheng,Haitao Zhang,Ming Liu,Chao Zheng,Ping Yan,Mali Gong

DOI: https://doi.org/10.1088/2040-8978/13/8/085204

IF: 2.1

2011-01-01

Journal of Optics

Abstract:We report on the fiber-based amplification of a flash lamp pumped Q-switched Nd:YAG laser. At a repetition rate of 10 Hz and spectrum width of 0.1 nm, an output single pulse energy of up to 12 mJ is generated in a 95 mu m core Yb-doped large mode area fiber with a seed pulse energy of 0.75 mJ and pulse duration of 11 ns. No stimulated Brillouin scattering, stimulated Raman scattering or saturation are observed. Furthermore, higher pulse energies will be achieved with higher pump powers.
10-µJ-level femtosecond pulse generation in the erbium CPA fiber source with microstructured hollow-core fiber assisted delivery and nonlinear frequency conversion

Alexander Krylov,Andrey Senatorov,Alexey Gladyshev,Yury Yatsenko,Alexey Kosolapov,Anton Kolyadin,Maxim Khudyakov,Mikhail Likhachev,Igor Bufetov

DOI: https://doi.org/10.1364/AO.494799

2023-07-20

Abstract:We report on the development of a chirped pulse amplification (CPA) designed erbium fiber source with a hybrid high-power amplifier, which is composed of erbium-doped and erbium/ytterbium-co-doped double-clad large-mode-area fibers. Stretched pulses from the high-power amplifier with up to 21.9 µJ energy and 198.5 kHz repetition rate are dechirped in the transmission grating pair-based compressor with 73% efficiency, yielding as short as 742 fs duration with 15.8 µJ energy and ≈13M W peak power (maximum average power up to 3.14 W) at the central wavelength of 1.56 µm. Compressed pulses are coupled into microstructured negative-curvature hollow-core fibers with a single row capillary cladding and different core sizes of 34 µm and 75 µm in order to realize femtosecond pulse delivery with a diffraction-limited output beam (M 2≤1.09) and demonstrate ∼200n J Stokes pulse generation at 1712 nm via rotational SRS in pressurized hydrogen (H 2). We believe that the developed system may be a prospect for high-precision material processing and other high-energy and high-peak-power laser applications.
1 kW, 10 mJ, 120 fs coherently combined fiber CPA laser system

Henning Stark,Joachim Buldt,Michael Müller,Arno Klenke,Jens Limpert

DOI: https://doi.org/10.48550/arXiv.2103.05614

2021-03-09

Optics

Abstract:An ultrafast fiber chirped-pulse amplification laser system based on coherent combination of 16 ytterbium-doped rod-type amplifiers is presented. It generates 10 mJ pulse energy at 1 kW average power and 120 fs pulse duration. A partially helium-protected, two-staged chirped-pulse amplification grating compressor is implemented to maintain the close to diffraction-limited beam quality by avoiding nonlinear absorption in air.
High Energy and High Peak Power Nanosecond Pulses Generated by Fiber Amplifier

Haitao Zhang,Xinglai Shen,Dan Chen,Chao Zheng

DOI: https://doi.org/10.1109/LPT.2014.2352864

2014-01-01

Abstract:Generation of nanosecond pulses with 55-mJ energy and 4.8-MW peak power are demonstrated in a multistage fiber amplifier system, which is seeded with 10-nm broadband pulses from a superluminescence diode. The pulses are at low repetition of 10 Hz and with width of 10 ns. High energy and high peak power for nanosecond pulses are obtained simultaneously from fiber amplifier. In particular, the peak power is at least two times the previous peak power for nanosecond pulses.
73 Nj, 109 Fs Yb-doped Fiber Laser at 19 MHz Repetition Rate in Amplifier Similariton Regime

Yizhou Liu,Yifan Cui,Jian Zhang,Aimin Wang,Zhigang Zhang

DOI: https://doi.org/10.1364/prj.3.000248

IF: 7.6

2015-01-01

Photonics Research

Abstract:We report femtosecond pulse generation in an amplifier similariton oscillator and a prechirped fiber amplifier system. The final output power is 1.4W, and the fundamental repetition rate is 19.1 MHz after a single state fiber amplifier. The pulsewidth is 109 fs.
Hybrid fiber-single crystal fiber chirped-pulse amplification system emitting more than 1.5 GW peak power with beam quality better than 1.3

Feng Li,Wei Zhao,Qianglong Li,Hualong Zhao,Yishan Wang,Yang Yang,Wenlong Wen,Xue Cao

DOI: https://doi.org/10.1109/jlt.2023.3312399

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:A hybrid chirped pulse amplification system composed by the monolithic fiber pre-amplifier and a two-stage single-pass single crystal fiber amplifier was demonstrated. A maximum power of 68 W at the repetition rate of 100 kHz was obtained. The laser pulses were amplified and then compressed using a 1600 line/mm grating pair compressor. A short pulse duration of 358 fs and a power of 54 W were obtained at 100 kHz, corresponding to a peak power of 1.508 GW, to the best of our knowledge, this is the highest peak power ever obtained from single crystal fiber at repetition rate above 100 kHz due to the consideration of the third order dispersion which was engraved in the stretcher and the tuning capacity of higher-order dispersion compensation of chirped fiber Bragg grating. Additionally, the beam quality better than 1.3 was obtained. This high peak power CPA system with excellent comprehensive parameters will find various applications in scientific research and industrial applications.

engineering, electrical & electronic,optics,telecommunications
A large dispersion-managed monolithic all-fiber chirped pulse amplification system for high-energy femtosecond laser generation

Feng Li,Wei Zhao,Yishan Wang,Na Wang,Qianglong Li,Yang Yang,Wenlong Wen

DOI: https://doi.org/10.1016/j.optlastec.2021.107684

2022-03-01

Abstract:A high energy monolithic all fiber chirped pulse amplification (CPA) system composed of fiber-silicate glass fiber is demonstrated in this work. In this compact system, the optical stretcher consists of two large dispersion chirped fiber Bragg gratings that offer a high stretch ratio to lower the nonlinearity that accumulates in the fiber amplifier. By employing high gain silicate glass fiber with a length of 20 cm as the main amplifier, an optimal balance of pulse energy and the B-integral is achieved. An amplified power of 42.6 W, corresponding to a pulse energy of 213 µJ, is obtained with an injection power of 100 mW. After compression, the laser pulses are compressed by a novel polarization-controlled double-pass configuration of a chirped volume Bragg grating (CVBG) to match the dispersion of the fiber stretcher. A total compression efficiency of 79.8% is obtained. The dispersion between the stretcher and the compressor is matched with the self-made temperature tuning device of the fiber grating. An optimized pulse width of 781 fs and a pulse energy of 170 µJ are obtained with the single-mode beam profile. To the best of our knowledge, this is the highest energy ever obtained with a single-mode beam profile for a spliced monolithic all-fiber CPA system. This compact high-energy fiber system will be useful in scientific research and industrial applications.

optics,physics, applied
Adaptively Controlled Sub-100 Fs Yb Fiber Chirped Pulse Amplification System

Jacob Lampen,Francesco Tani,Peng Li,Kevin F. Lee,Jie Jiang,Philip St.J. Russell,Martin E. Fermann

DOI: https://doi.org/10.1364/cleo_si.2023.sf3h.8

2023-01-01

Abstract:Bandwidth limited 92 fs 10 µJ pulses are generated using an adaptive fiber Bragg grating stretcher for group delay and an adjus table Lyot filter for bandwidth control, and compressed to 12 fs in a hollow-core fiber.

A Two-Stage Chirped Pulse Fiber Amplifier System for Lasik

Vector-dispersion Compensation and Pulse Pedestal Cancellation in a Femtosecond Nonlinear Amplification Fiber Laser System.

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

Microjoule Level Femtosecond Optical Pulses with Double-Cladding Fiber-Based Nonlinear Chirped-Pulse Amplification

Chirped Pulse Amplified Dissipative-Soliton Erbium-doped Fiber Lasers

Yb-Doped Fiber Chirped Pulse Amplification System Delivering 1 mJ, 231 fs at 1 kHz Repetition Rate

All-Fiber-Based Ultrashort Pulse Generation and Chirped Pulse Amplification Through Parametric Processes

Low repetition rate broadband high energy and peak power nanosecond pulsed Yb-doped fiber amplifier

Nanosecond Pulse Shaping with Fiber-Based Electro-Optical Modulators and a Double-Pass Tapered Amplifier

Optical Parametric Chirped Pulse Amplification Based on Photonic Crystal Fibre

Femtosecond fiber laser for femtosecond LASIK

Development of a Femtosecond High-Power Ytterbium-doped Fiber Laser System and Study on Spiky Spectral Modulation in Highly Nonlinear Chirped-Pulse Fiber Amplifiers

Amplification of arbitrary frequency chirps of pulsed light on nanosecond timescales

A 12 Mj 11 Ns Spectrally Narrow Fiber Amplifier with A Pulsed Pump

10-µJ-level femtosecond pulse generation in the erbium CPA fiber source with microstructured hollow-core fiber assisted delivery and nonlinear frequency conversion

1 kW, 10 mJ, 120 fs coherently combined fiber CPA laser system

High Energy and High Peak Power Nanosecond Pulses Generated by Fiber Amplifier

73 Nj, 109 Fs Yb-doped Fiber Laser at 19 MHz Repetition Rate in Amplifier Similariton Regime

Hybrid fiber-single crystal fiber chirped-pulse amplification system emitting more than 1.5 GW peak power with beam quality better than 1.3

A large dispersion-managed monolithic all-fiber chirped pulse amplification system for high-energy femtosecond laser generation

Adaptively Controlled Sub-100 Fs Yb Fiber Chirped Pulse Amplification System