Abstract:For the feasibility study of Pb-Bi-cooled fast reactors (FR) and the Pb-Bi target of accelerator-driven nuclear transmutation systems , Pb-Bi flow technologies were developed and steel corrosion behavior in a Pb-Bi flow was investigated using a Pb-Bi circulation loop. The performance of an electro-magnetic flow meter with electrically insulated electrodes plated with Rh was better than those of conventional and tubular types. Oxygen concentration was controlled by continuous injection of Ar, H2 and H2O mixture gas into the Pb-Bi flow. In order to have desired oxygen potential, the partial pressure ratio of PH2/PH2O was chosen in the range from 0.12 to 2.2 by bubbling the mixture of Ar and H2 in water columns at the room temperature. By injecting the mixture gas into the loop for sufficient time, the oxygen potentials measured by the oxygen sensor made of solid electrolyte ZrO2-Y2O3 agreed well with those in the injected gas mixture. In the first corrosion test, steels were exposed to a Pb-Bi flow at the temperature of 550 °C, the velocity of 2 m/s and the oxygen concentration of ∼5.0×10−7 wt.% for 959 hours. It was found that the weight loss was larger in the order of SS316, low Cr steel (SCM420) and high Cr steels (STBA26, SUS405, SUS430). Corrosion was suppressed by a Cr oxide layer for high Cr steels. A porous layer was formed on SS316 surface due to high solubility of Ni in Pb-Bi. In the second corrosion test, the oxygen concentration was kept at 3.6×10−7 wt.% by injecting Ar, H2 and H2O mixture gas into a Pb-Bi flow, and steels were exposed to a Pb-Bi flow at the temperature of 550 °C, the velocity of 2 m/s for 1000 hours. Serious erosion damage was observed in SCM420 at the entrance, and some erosion damages appeared in low Cr steels: SCM420, F82H, STBA26 and HCM12 downstream. Crack type damage was observed on the surface of HCM12, and pitting-type damage was observed on the surface of 2 1/4Cr-1Mo steel. Some penetration of Pb-Bi into the materials appeared in some of the erosion-damaged steels.

Corrosion–erosion test of SS316L grain boundary engineering material (GBEM) in lead bismuth flowing loop

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

High-Temperature Corrosion Behaviors of Structural Materials for Lead-Alloy-Cooled Fast Reactor Application

Corrosion Studies in Support of Medium-Power Lead-Alloy-Cooled Reactor

Analysis of 316L stainless steel pipe of lead–bismuth eutectic cooled thermo-hydraulic loop

Ultrasonic cavitation erosion of 316L steel weld joint in liquid Pb-Bi eutectic alloy at 550°C

Insight into the fretting corrosion behavior of 316L steel in liquid lead-bismuth eutectic at 500°C

Early stages of dissolution corrosion in 316L and DIN 1.4970 austenitic stainless steels with and without anticorrosion coatings in static liquid lead-bismuth eutectic (LBE) at 500$^\circ$C

Study on the Corrosion Behavior of Aluminum Reinforced Austenitic Steel in Liquid Lead Bismuth at 550 °C

Effects of Grain Boundary Engineering on the Microstructure and Corrosion Fatigue Properties of 316L Austenitic Stainless Steel

Erosion-corrosion of 304N austenitic steels in liquid Pb Bi flow perpendicular to steel surface

Corrosion Kinetics and Mechanisms of 15-15Ti Steel in Flowing Liquid Lead-Bismuth Eutectic at 500°C

Oxidation and dissolution behavior of FeCrNiAl based high entropy alloy and alumina-forming austenitic steel exposed to lead-bismuth eutectic (LBE)

Experimental Study on Flow Technology and Steel Corrosion of Lead-Bismuth

Evaluation of Grain Boundary Network and Improvement of Intergranular Cracking Resistance in 316L Stainless Steel after Grain Boundary Engineering

MEASUREMENTS OF FINE STRUCTURES IN THE LEAD-BISMUTH EUTECTIC ALLOY MELTS BY DIFFERENTIAL SCANNING CALORIMETRY

Investigation on fretting wear mechanism of 316 stainless steel induced by Ni dissolution during pre-immersion corrosion in the liquid lead-bismuth eutectic (LBE)

Transmission electron microscopy (TEM) on oxide layers formed on D9 stainless steel in lead bismuth eutectic (LBE)

Wetting Behavior of LBE on Corroded Candidate LFR Structural Materials of 316L, T91 and CLAM

Experimental study on corrosion compatibility of laser-welded ODS steel with liquid lead lithium