Abstract:Here we report an optical fiber sensor capable of performing strain-insensitive simultaneous measurement of bending and temperature using a long-period fiber grating (LPFG) inscribed on doubleclad fiber (DCF) with a CO₂ laser at ˜10.6 μm. The LPFG inscribed on DCF, referred to as a DC-LPFG, was fabricated by scanning CO₂ laser pulses on an unjacketed DCF with a specific period. Due to co-directional mode coupling, the fabricated DC-LPFG has discrete attenuation bands widely distributed over hundreds of nanometers. Among these wavelength-dependent loss dips, adjacent two dips with different resonance wavelengths were selected as sensor indicators for the measurement of bending and temperature. For these two indicator dips designated as dips A and B, their bending and temperature responses were investigated in a curvature range of 4.90 to 21.91 m-1 and a temperature range of 30 to 110 °C. With increasing bending applied to the DC-LPFG at room temperature, dips A and B showed different blue shifts. The bending sensitivities of dips A and B were measured to be approximately -0.77 and 0.51 nm/m-1, respectively. Unlike the bending response, they showed red shifts of different amounts with increasing ambient temperature, while the sensor head (i.e., the DC-LPFG) remained straight without any applied bending. The temperature sensitivities of dips A and B were measured to be ˜0.094 and ˜0.078 nm/°C, respectively. Owing to their linear and independent responses to bending and temperature, bending and temperature changes applied to the DC-LPFG could be simultaneously estimated from the measured wavelength shifts of the two indicator dips using their pre-determined bending and temperature sensitivities. Moreover, in a strain range of 0 to 2200 με (step: 200 με), strain-induced spectral variations of dips A and B were also measured, and the strain sensitivities of dips A and B were evaluated as approximately -0.028 and -0.013 pm/με, respectively. These strain-induced wavelength shifts were so small that they had little effect on the measurement results of bending and temperature. Thus, it is concluded that the fabricated DC-LPFG can be employed as a cost-effective sensor head for strain-insensitive separate measurement of bending and temperature.

Temperature Insensitive Optical Fiber Laser Bend Sensor with A Low Detection Limit

Highly Sensitive Temperature Sensor Using Intrinsic Mach-Zehnder Interferometer Formed by Bent Micro-Fiber Embedded in Polymer

Integrated All-Fiber Sensor for Simultaneous Measurements of Curvature and Temperature

Inexpensive optical fiber Fabry–Perot microcavity with controllable length for sensitive temperature measurements

An Inline Fiber Curvature Sensor Based on Eccentric Core Fiber and Off-Axis Air Cavity Fabry-Pérot Interferometer

Highly Compact Vector Bending Sensor With Microfiber-Assisted Mach– Zehnder Interferometer

Optical Fiber Sensor for Curvature and Temperature Measurement Based on Anti-Resonant Effect Cascaded with Multimode Interference

Femtosecond laser inscribed straight waveguide in no-core fiber for in-line Mach–Zehnder interferometer construction

A Reliable Anti-Interference Temperature Sensor Based on a Four-Hole Microstructure Optical Fiber Mach-Zehnder Interferometer.

Temperature-compensated fiber directional-bend sensor based on a sandwiched MMF–PMPCF structure

Ultra-short cavity distributed bragg reflector Er-doped fiber laser for temperature-insensitive bending measurement

Light Intensity Modulation Temperature Sensor Based on U-shaped Bent Single-Mode Fiber

Curvature sensor based on femtosecond laser-inscribed straight waveguide in FMF

High-Performance Bending Sensor Based on Femtosecond Laser-Inscribed in-Fiber Mach–Zehnder Interferometer

Highly Sensitive Bending Sensor Based on Er^3+-doped DBR Fiber Laser

In-Line Hybrid Fiber Sensor for Curvature and Temperature Measurement

Fiber-Optic Bend Sensor Using Lp21 Mode Operation

Strain-Insensitive Simultaneous Measurement of Bending and Temperature Using Long-Period Fiber Grating Inscribed on Double-Clad Fiber with CO₂ Laser

Experimental demonstration of an angle laser sensor based on an optical thinned microfiber Mach-Zehnder interferometer

Highly sensitive bending sensor based on Er3+-doped DBR fiber laser