Abstract:Here we report an optical fiber sensor capable of performing strain-insensitive simultaneous measurement of bending and temperature using a long-period fiber grating (LPFG) inscribed on doubleclad fiber (DCF) with a CO₂ laser at ˜10.6 μm. The LPFG inscribed on DCF, referred to as a DC-LPFG, was fabricated by scanning CO₂ laser pulses on an unjacketed DCF with a specific period. Due to co-directional mode coupling, the fabricated DC-LPFG has discrete attenuation bands widely distributed over hundreds of nanometers. Among these wavelength-dependent loss dips, adjacent two dips with different resonance wavelengths were selected as sensor indicators for the measurement of bending and temperature. For these two indicator dips designated as dips A and B, their bending and temperature responses were investigated in a curvature range of 4.90 to 21.91 m-1 and a temperature range of 30 to 110 °C. With increasing bending applied to the DC-LPFG at room temperature, dips A and B showed different blue shifts. The bending sensitivities of dips A and B were measured to be approximately -0.77 and 0.51 nm/m-1, respectively. Unlike the bending response, they showed red shifts of different amounts with increasing ambient temperature, while the sensor head (i.e., the DC-LPFG) remained straight without any applied bending. The temperature sensitivities of dips A and B were measured to be ˜0.094 and ˜0.078 nm/°C, respectively. Owing to their linear and independent responses to bending and temperature, bending and temperature changes applied to the DC-LPFG could be simultaneously estimated from the measured wavelength shifts of the two indicator dips using their pre-determined bending and temperature sensitivities. Moreover, in a strain range of 0 to 2200 με (step: 200 με), strain-induced spectral variations of dips A and B were also measured, and the strain sensitivities of dips A and B were evaluated as approximately -0.028 and -0.013 pm/με, respectively. These strain-induced wavelength shifts were so small that they had little effect on the measurement results of bending and temperature. Thus, it is concluded that the fabricated DC-LPFG can be employed as a cost-effective sensor head for strain-insensitive separate measurement of bending and temperature.

Ultra-short cavity distributed bragg reflector Er-doped fiber laser for temperature-insensitive bending measurement

Highly Sensitive Bending Sensor Based on Er^3+-doped DBR Fiber Laser

Highly sensitive bending sensor based on Er3+-doped DBR fiber laser

Bending-induced Sensing Sensitivity in Single-Longitude-mode DBR Fiber Laser

DBR-fiber-laser-based active temperature sensor and its applications in the measurement of fiber birefringence

Compact polarimetric heterodyning DBR fiber laser sensor with high temperature resistance

High-Resolution Strain/Temperature Sensing System Based on A High-Finesse Fiber Cavity and Time-Domain Wavelength Demodulation

Compact Bending Sensor Based on a Fiber Bragg Grating in an Abrupt Biconical Taper.

Temperature Insensitive Optical Fiber Laser Bend Sensor with A Low Detection Limit

An Ultra-High-Resolution Bending Temperature Decoupled Measurement Sensor Based on a Novel Core Refractive Index-like Linear Distribution Doped Fiber

Sensitivity Enhanced Distributed Brillouin Curvature Sensor Based on Erbium-Doped Few-Mode Fiber

Short Cavity Single Frequency Fiber Laser for In-Situ Sensing Applications over A Wide Temperature Range

High-Resolution Strain and Temperature Sensor Based on Distributed Bragg Reflector Fiber Laser

Investigation of DBR Fiber Laser Sensing Based on Beat Frequency Interrogation and Its Networking Technique

Femtosecond Laser Inscription of Fiber Bragg Grating in Twin-Core Few-Mode Fiber for Directional Bend Sensing

Ultra-short DBR Fiber Laser with High-Temperature Resistance Using Tilted Fiber Bragg Grating Output Coupler.

Bragg grating tuned fiber laser system for measurement of wider range temperature and strain

Bending-Loss-Resistant Distributed Temperature and Strain Discriminative Brillouin Sensor Based on 98 mol% Germania-Doped Few-Mode Fiber

In-fiber Torsion and Temperature Measurement Based on Femtosecond-Laser-inscribed Eccentric Fiber Bragg Grating

Highly Sensitive Vector Bending Sensor Based on an Embedded Multimode D-shaped LPFG.

Strain-Insensitive Simultaneous Measurement of Bending and Temperature Using Long-Period Fiber Grating Inscribed on Double-Clad Fiber with CO₂ Laser