Abstract:Here we report an optical fiber sensor capable of performing strain-insensitive simultaneous measurement of bending and temperature using a long-period fiber grating (LPFG) inscribed on doubleclad fiber (DCF) with a CO₂ laser at ˜10.6 μm. The LPFG inscribed on DCF, referred to as a DC-LPFG, was fabricated by scanning CO₂ laser pulses on an unjacketed DCF with a specific period. Due to co-directional mode coupling, the fabricated DC-LPFG has discrete attenuation bands widely distributed over hundreds of nanometers. Among these wavelength-dependent loss dips, adjacent two dips with different resonance wavelengths were selected as sensor indicators for the measurement of bending and temperature. For these two indicator dips designated as dips A and B, their bending and temperature responses were investigated in a curvature range of 4.90 to 21.91 m-1 and a temperature range of 30 to 110 °C. With increasing bending applied to the DC-LPFG at room temperature, dips A and B showed different blue shifts. The bending sensitivities of dips A and B were measured to be approximately -0.77 and 0.51 nm/m-1, respectively. Unlike the bending response, they showed red shifts of different amounts with increasing ambient temperature, while the sensor head (i.e., the DC-LPFG) remained straight without any applied bending. The temperature sensitivities of dips A and B were measured to be ˜0.094 and ˜0.078 nm/°C, respectively. Owing to their linear and independent responses to bending and temperature, bending and temperature changes applied to the DC-LPFG could be simultaneously estimated from the measured wavelength shifts of the two indicator dips using their pre-determined bending and temperature sensitivities. Moreover, in a strain range of 0 to 2200 με (step: 200 με), strain-induced spectral variations of dips A and B were also measured, and the strain sensitivities of dips A and B were evaluated as approximately -0.028 and -0.013 pm/με, respectively. These strain-induced wavelength shifts were so small that they had little effect on the measurement results of bending and temperature. Thus, it is concluded that the fabricated DC-LPFG can be employed as a cost-effective sensor head for strain-insensitive separate measurement of bending and temperature.

Fiber-Optic Bend Sensor Using Lp21 Mode Operation

Coiling an Optical Fiber for Long-Range Dynamic Displacement and Force Sensing

Curvature and angle sensor based on LP 21 mode reflected by a four-mode fiber Bragg grating

Integrated All-Fiber Sensor for Simultaneous Measurements of Curvature and Temperature

An Inline Fiber Curvature Sensor Based on Eccentric Core Fiber and Off-Axis Air Cavity Fabry-Pérot Interferometer

Highly Sensitive Vector Bending Sensor Based on an Embedded Multimode D-shaped LPFG.

Optical Fiber Bending Sensor Based on Michelson Interferometer

Effects of Twisting and Bending on LP21 Mode Propagation in Optical Fiber.

Compact Robust Vector Bending Sensor Based on Single Stress-Applying Fiber

Temperature Insensitive Optical Fiber Laser Bend Sensor with A Low Detection Limit

Bending-Loss-Resistant Distributed Temperature and Strain Discriminative Brillouin Sensor Based on 98 mol% Germania-Doped Few-Mode Fiber

Simultaneous Measurement of Knuckle Flexion and Temperature With a Few-Mode FBG

Two-Axis Bending Sensor Based on Asymmetric Grid Long-Period Fiber Grating

Strain-Insensitive Simultaneous Measurement of Bending and Temperature Using Long-Period Fiber Grating Inscribed on Double-Clad Fiber with CO₂ Laser

Flexible Photonic Sensors: Investigation of an Approach Based on Ratiometric Power in Few-Mode Waveguides for Bending Measurement

A Wide Range Curvature Sensor Based on Fiber Ring Laser With a Long-Period Fiber Grating

Highly Compact Vector Bending Sensor With Microfiber-Assisted Mach– Zehnder Interferometer

A Vector Bending Sensor Based on a Core-Offset Long Period Fiber Grating Induced by an Arc-Discharge

Temperature-compensated fiber directional-bend sensor based on a sandwiched MMF–PMPCF structure

Sensitivity-enhanced two-dimensional bending sensor based on single-mode fiber measurement

Bending-Loss-Resistant Brillouin Optical Time-Domain Analysis Based on Thin-Diameter Fiber