Abstract:Here we report an optical fiber sensor capable of performing strain-insensitive simultaneous measurement of bending and temperature using a long-period fiber grating (LPFG) inscribed on doubleclad fiber (DCF) with a CO₂ laser at ˜10.6 μm. The LPFG inscribed on DCF, referred to as a DC-LPFG, was fabricated by scanning CO₂ laser pulses on an unjacketed DCF with a specific period. Due to co-directional mode coupling, the fabricated DC-LPFG has discrete attenuation bands widely distributed over hundreds of nanometers. Among these wavelength-dependent loss dips, adjacent two dips with different resonance wavelengths were selected as sensor indicators for the measurement of bending and temperature. For these two indicator dips designated as dips A and B, their bending and temperature responses were investigated in a curvature range of 4.90 to 21.91 m-1 and a temperature range of 30 to 110 °C. With increasing bending applied to the DC-LPFG at room temperature, dips A and B showed different blue shifts. The bending sensitivities of dips A and B were measured to be approximately -0.77 and 0.51 nm/m-1, respectively. Unlike the bending response, they showed red shifts of different amounts with increasing ambient temperature, while the sensor head (i.e., the DC-LPFG) remained straight without any applied bending. The temperature sensitivities of dips A and B were measured to be ˜0.094 and ˜0.078 nm/°C, respectively. Owing to their linear and independent responses to bending and temperature, bending and temperature changes applied to the DC-LPFG could be simultaneously estimated from the measured wavelength shifts of the two indicator dips using their pre-determined bending and temperature sensitivities. Moreover, in a strain range of 0 to 2200 με (step: 200 με), strain-induced spectral variations of dips A and B were also measured, and the strain sensitivities of dips A and B were evaluated as approximately -0.028 and -0.013 pm/με, respectively. These strain-induced wavelength shifts were so small that they had little effect on the measurement results of bending and temperature. Thus, it is concluded that the fabricated DC-LPFG can be employed as a cost-effective sensor head for strain-insensitive separate measurement of bending and temperature.

Simultaneous Measurement of Knuckle Flexion and Temperature With a Few-Mode FBG

Integrated All-Fiber Sensor for Simultaneous Measurements of Curvature and Temperature

Simultaneous measurement of temperature and bend by using an eccentric core fiber Bragg grating cascaded with a Fabry-Perot cavity

Simultaneous Measurement of Pressure and Temperature Using a Single Fiber Bragg Grating

Strain-Insensitive Simultaneous Measurement of Bending and Temperature Using Long-Period Fiber Grating Inscribed on Double-Clad Fiber with CO₂ Laser

Simultaneous Measurement of Curvature Vector and Temperature Based on Composite Gratings Inscribed on D-Shaped Fiber

Simultaneous Measurement of Strain and Temperature by Two Peanut Tapers with Embedded Fiber Bragg Grating.

Simultaneous Measurement of Temperature and Strain Based on Fiber Loop Mirror Combined with Fiber Bragg Grating

Simultaneous Measurement of Temperature and Strain Based on Compact Parallel Core–Cladding FBGs Inscribed by Femtosecond Laser Point-by-Point Method

Simultaneous Strain and Temperature Measurement Using an Integrated Fibre Bragg Grating Extrinsic Fabry-Perot Sensor

Joint-peaks Demodulation Method Based on Multireflection Peaks of a Few-Mode Fiber Bragg Grating for Reducing Sensing Error

Simultaneous strain and temperature measurement by cascading few-mode fiber and single-mode fiber long-period fiber gratings

Design and Analysis of a Combined FBG Sensor for the Measurement of Three Parameters.

Curvature and angle sensor based on LP 21 mode reflected by a four-mode fiber Bragg grating

Air Gap Fiber Bragg Grating for Simultaneous Strain and Temperature Measurement

Dual-dip Long-Period Fiber Gratings for Directional Bending Measurement

Simultaneous Strain and Temperature Measurements in Composites Using A Multiplexed Fibre Bragg Grating Sensor and an Extrinsic Fabry-Perot Sensor

Multiparameter Measurements for Bending, Torsion, and Temperature by Long-Period Gratings in Three-Core Fiber

Multi-parameter sensor based on cascaded multicore FBGs and an FPI for bending, temperature and pressure measurements

Temperature and strain simultaneous sensing measurement based on an all-fiber Mach-Zehnder interferometer and fiber Bragg grating

Sensitivity-enhanced two-dimensional bending sensor based on single-mode fiber measurement