Abstract:Polymer electrolyte membrane fuel cells (PEMFCs) have widely been considered environmental friendly alternative energy technologies due to their high energy conversion efficiency and zero emission. In the recent, the importance of performance and durability of electrolyte membrane, interfacial layer separating two electrodes, prohibiting fuel cross-over, while transporting only protons, has become much crucial for utilizing PEMFCs to the automobile applications such as fuel cell electric vehicles (FCEVs) and drones. Unfortunately, the current state membranes, mainly composed of perfluorosulfonic acid (PFSA) ionomers, have suffered from the high cost and low proton conductivity, and low dimensional stability during dynamic humidity changes during fuel cell operation. In order to deal with these issues, recently, a reinforced composite membranes (RCMs) have been developed in which a PFSA ionomer is impregnated into a porous support matrix consisted with nanofibrous polymer materials such as polytetrafluoroethylene (PTFE) due to their thermal/mechanical robustness. The PTFE based RCMs could provide enhanced mechanical stability and electrochemical performance with a reduced use of PFSA ionomer, but low impregnation of ionomers into nanosized hydrophobic PTFE networks, resulting in phase separation and irreversible creep deformation. Herein, we report a novel preparation of vertically alined PTFE aggregated fibers (PTFE AFs) as a reinforcement by using facile electrospinning hetero-polymer solutions containing PTFE nanoparticles and PEO (Polyethylene oxide) carrier polymer and subsequent thermal removal of PEO. Developed PTFE AF were effectively soaked by PFSA ionomers, and PTFE AF based RCMs delivered outstanding dimensional stability and proton conductivity compared to commercial RCMs. Furthermore, PTFE AF based RCMs used MEA exhibited exceptional single-cell performance and long-term stability. The enhanced performance was attributed to the facile proton conduction through the one dimensional channels between aligned fibers without fiber scattering, and effective suppression of volume expansion of hydrated PFSA ionomer by rectangular shaped PTFE fiber network. We believe the widespread use of novel PTFE fiber based membranes with an unique pattern in a variety of membrane applications where porous supports are used. Figure 1

Radiolytic Fabrication and Characterization of Ptfe-G-Paa As the Supporters for the Reinforced Composite Fuel Cell Membrane

Improving the Hydrophilicity of Poly(vinylidene Fluoride) Porous Membranes by Electron Beam Initiated Surface Grafting of AA/SSS Binary Monomers

Poly(vinylidene Fluoride) with Grafted Poly(ethylene Glycol) Side Chains Via the RAFT-Mediated Process and Pore Size Control of the Copolymer Membranes

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Controlled Grafting of Comb Copolymer Brushes on Poly(tetrafluoroethylene) Films by Surface-Initiated Living Radical Polymerizations.

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Cross-Aligned PTFE Nanofiber Reinforced Composite Membrane for PEM Fuel Cells

Surface‐initiated Atom Transfer Radical Polymerization from Porous Poly(tetrafluoroethylene) Membranes Using the CF Groups As Initiators

Study on the mechanism of graft polymerization and sulfonation of proton exchange membranes for fuel cell

Effects of Polymer Architecture and Composition on the Adhesion of Poly(tetrafluoroethylene)

Thermal imidization of poly(amic acid) precursors on surface-modified poly(tetrafluoroethylene) films via graft copolymerization with glycidyl methacrylate

Quantitative analysis of proton exchange membrane prepared by radiation-induced grafting on ultra-thin FEP film

Hydrocarbon‐Based Ionomer/PTFE‐Reinforced Composite Membrane Through Multibar Coating Technique for Durable Fuel Cells

Preparation of a Novel Proton Exchange Membrane Using Radiation Grafted ETFE Film for Fuel Cell

Tethering Hydrophilic Polymer Brushes Onto PPESK Membranes Via Surface-Initiated Atom Transfer Radical Polymerization

Preparation Of Pda/Tio2 Composite Film On Ptfe And Its Cellular Response

Preparation and characterization of chemically stable polymer electrolyte membranes by radiation-induced graft copolymerization of four monomers into ETFE films

Surface modification of polytetrafluoroethylene (PTFE) fibers through methyl methacrylate (MMA) polymerization for self-lubricating composites

Reinforced Composite Membranes Based on Expanded Polytetrafluoroethylene Skeletons Modified by a Surface Sol–Gel Process for Fuel Cell Applications

Porous Polyethylene Supports in Reinforcement of Multiblock Hydrocarbon Ionomers for Proton Exchange Membranes

Preparation and evaluation of a novel self-humidifying Pt/PFSA composite membrane for PEM fuel cell