Abstract:Conventional methods for hot extrusion of magnesium (Mg) alloy sheets have limitations for microstructure improvement and mechanical property enhancement. Co-extrusion of Mg alloy with an Al alloy core provides an opportunity for refining the grain size and improving basal texture. This study introduces a novel severe plastic deformation (SPD) method, Direct Extrusion-Continuous Shear (DE-CS), utilizing 6063 Al alloy as the core to fabricate innovative Mg/Al clad composite sheets. Monolithic Mg sheets (non-co-extruded condition) are extruded under identical conditions for comparison. By evaluating the microstructure and mechanical properties of AZ31 Mg alloy under co-extrusion and non-co-extrusion conditions, the positive effect of Mg-Al composite billet co-extrusion on AZ31 Mg alloy is established. The grain refinement effect in co-extruded samples is superior, enhancing plasticity without significant reduction in tensile strength. The microstructure evolution and dynamic recrystallization (DRX) behaviour of AZ31 Mg alloy during co-extrusion were analyzed comprehensively. The results indicate that, in the initial stages of deformation, various variants of {10-12} extension twins (ETs) play a crucial role in refining the original grains, forming initial [10-10]//ED fiber texture components alongside other non-basal components. Upon entering the shear deformation (SD) zone, deformed twins disappear, and small dynamically recrystallized (DRXed) grains emerge along boundaries of coarse deformation grains and within the grains. Strong shear deformations and compressive stress from transverse direction (TD) induce intensified prismatic and pyramidal slip, promoting continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX). CDRX predominantly affects elongated deformed grains, forming an [10-10]//ED fiber texture through high-energy grain boundary segmentation. Subsequently, compatible stress increases due to the activity of non-basal slip dislocation and the reduction in grain boundary (GB) size. DDRX emerges as the dominant mechanism, generating randomized [10-10]//ED fiber and non-fiber textures within parent grains and at boundaries.

Deformation behavior and interface microstructure evolution of Al/Mg/Al multilayer composite sheets during deep drawing

Achieving three-layered Al/Mg/Al sheet via combining porthole die co-extrusion and hot forging

Interfacial microstructure evolution for coordinated deformation of Mg/Al composite plates by asymmetrical rolling with differential temperature rolls

Effect of thickness ratio on microstructure evolution and coordinated behavior of Mg/Al composite plates in one-pass asymmetric rolling with differential temperature rolls

Effect of Deep-Cooling Rolling Deformation on the Microstructure and Mechanical Properties of an Al-4.5Cu-1.5Mg-0.6Mn-0.2Ti Alloy

Response Mechanism of Mechanical Behavior with Mg Plate Microstructure Evolution During Al/Mg/Al Composite Plate Rolled by hard Plate

Enhancing formability in deep drawing: A 3D finite element analysis of plastic wrinkling in AA2090 Al–Li alloy

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature

A study on the microstructural evolution of copper/aluminum composite strips fabricated by micro flexible rolling

Drawing Process and Properties of Roll-casting AZ31 Magnesium Alloy Sheet

Effect of differential temperature on the interfacial microstructure evolution and mechanical properties of asymmetrically rolled Mg/Al composite plates

Effect of cumulative deformation and interlayer mechanical properties on bonding strength of corrugated interface steel/aluminum composite plate

Microstructural characterization and mechanical behavior of Mg-AZ31B/Al 6063 bimetallic sheets produced by combining continuous shear deformation with direct extrusion

Hot compressive deformation of eutectic Al-17at% Cu alloy on the interface of the Cu-Al composite plate produced by horizontal continuous casting

Deformation Behavior and Microstructure Evolution of AZ31 Mg Alloy by Forging–Bending Repeated Deformation with Multi-pass Lowered Temperature

An integrated computational and experimental study of the failure mode in Mg/Al laminated composite under three-point bending

Deep Drawability of Al-Mg Alloys Produced by Twin Roll Continuous Casting Method: Investigation of Microstructure and Mechanical Properties

Microstructure and mechanical behavior of Mg ZK60/Al 1100 composite plates fabricated by co-extrusion

Deformation behaviour, microstructure evolution and dynamic recrystallization mechanism of AZ31 magnesium alloy under co-extruded by Mg-Al composite billet

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

Annealing coordinates the deformation of shear band to improve the microstructure difference and simultaneously promote the strength-plasticity of composite plate