Abstract:Blank holder force (BHF) is one of the important process parameters in the deep drawing process. BHF helps produce defect-free components by controlling metal flow during the deep drawing process. If BHF is low, it causes wrinkling; otherwise, it causes the sheet to rupture. Therefore, optimization of BHF is an important issue in industries. One of the effective approaches to determining optimal BHF is to study forming force, thickness distribution, and wrinkles to produce a deep-drawn cup. The main function of this approach is that it minimizes the maximum forming force and prevents process limits. Therefore, this study aims to investigate the relationship between the BHF and forming force through experimental and simulation results. In addition, the effect of BHF on the thickness distribution and wrinkling is considered. Hence, numerical and experimental methods were employed for St14 and SS304L sheets with thicknesses of 0.5, 1, and 1.5 mm to achieve the objectives. Firstly, the simulation of the process was performed to study the mechanical behavior. Then, a set of experimental tests were conducted to validate the simulations. Finally, utilizing the experimental and numerical results, the optimal BHF value was determined. It was observed that the maximum thinning and maximum forming force are related to the forming process without BHF. Moreover, when the wrinkling at the edge of the part was removed by gradually increasing BHF, the minimum values of forming force and thinning were obtained. According to the investigations carried out on three thicknesses, it was observed that by reducing the thickness from 1.5 to 0.5 mm, the maximum forming force decreases in both SS304L and St14 sheets. However, the acquired results showed that the minimum optimal BHF is obtained in both sheets at a thickness of 1.5 mm. Overall, this research provides valuable experimental and numerical guidance for implementing the deep drawing process to manufacture cylindrical parts with minimum forming force required to save energy consumption.

Enhancing formability in deep drawing: A 3D finite element analysis of plastic wrinkling in AA2090 Al–Li alloy

Steel-aluminum Plastic Clinching of an Inclined Wall Die

Evaluation of the Effect of Contact and Friction on Deep Drawing Formability Analysis for Lightweight Aluminum Lithium Alloy Using Cylindrical Cup

Effect of process parameters on the deep drawing formability of aluminum and advanced high-strength steel square cups

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing

Multi-scale numerical investigation of deep drawing of 6K21 aluminum alloy by crystal plasticity and a stress-invariant based anisotropic yield function under non-associated flow rule

Research on 5A06 Aluminium Alloy Thin-wall Semisphere Hydromechanical Deep Drawing Process

Loading conditions constrained wrinkling behaviors of thin-walled sheet/tube parts during metal forming

Formability limits by wrinkling in sheet metal forming

Failure control on hydroforming process of thin-walled aluminum alloy with complex surface covers

Investigation of forming defects in 5A06 aluminum alloy cold stamping of thin-walled shell with corner

Thermo-mechanical finite element analysis of the AA5086 alloy under warm forming conditions

Finite Element Modeling for Deep-Drawing of Aluminum Alloy Sheet 6014-T4 Using Anisotropic Yield and Non-Afr Models

Effects of anisotropic yield criteria on the prediction of wrinkle during the deep-drawing forming of aluminum alloy sheet

Study on hydroforming of AA6061-T6 aluminum alloy sheet based on upper sheet

Experimental and numerical investigation to determine the optimal blank-holder force in deep drawing process based on forming force for SS304L and St14 sheets

Wrinkling and Strengthening Behaviors in the Two-Layer-Sheet Hot-Forming–Quenching Integrated Process for an Al–Cu–Mg-Alloy Thin-Walled Curved-Surface Shell

Analysis of the Stamping Speed for Sheet Metal Forming of Aluminum Alloy 5052-H112

A Novel Method for Friction Coefficient Calculation in Metal Sheet Forming of Axis-Symmetric Deep Drawing Parts

Research on incremental forming simulation based on an improved constitutive model

Anisotropic plasticity deformation during micro-deep drawing of 304 foils: An experimental and numerical investigation