Abstract:A discrete element method (DEM) model was developed for a co-rotating twin-screw mixer (TSM) consisting of conveying and kneading elements. This model was used to simulate the mixing of a cohesive binary system of particles (P1 and P2). The particles were calibrated using angle of repose and dynamic yield strength simulations. Properties of P1 were kept constant throughout the study while properties of P2 were varied. The TSM model was used to study the influence of particle size, density, and flowability of P2 on process outputs such as powder holdup, mean residence time (MRT), and degree of mixing along the length of the TSM. All the three particle properties were varied at three-factor levels with flowability ranging from good flow (GF), poor flow (PF), and very very poor flow (VVPF) based on Carr’s classification. The model provides fundamental insights into the differences in mixing in the conveying sections of the mixer for materials with different flowability. Due to the co-rotating nature of the screws, the majority of the material in the conveying sections was carried on one side of the TSM for GF and PF particles, while both the screws carried VVPF particles. The total steady-state holdup and the mean residence time (MRT) of particles inside the TSM were heavily influenced by particle flowability compared to the other two tested particle parameters. The holdup in the conveying compartments ranged from 11%–15% of the total holdup, while the kneading compartment comprised 40% of the total holdup in the mixer. The simulations found that VVPF particles mixed the fastest and that the GF particles had the highest tendency to demix. The model was also used to suggest and test other screw design configurations to improve mixing. A screw design with kneading elements closer to the mixer outlet resulted in better mixing of GF particles. A screw design consisting only of conveying elements achieved the same degree of mixing as the original screw design for VVPF particles.

Numerical Investigation on the Effect of the Particle Feeding Order on the Degree of Mixing Using DEM

Studying on the Upper Limit of the Coarse-Grained DEM Model for Simulating Mixing Processes in a Rolling Drum with Complex Wall Boundary

Numerical Study on Particle Mixing in a Double-Screw Conical Mixer

Hydrodynamics and mixing process in a horizontal self-cleaning opposite-rotating twin-shaft kneader

An Experimentally Validated Coarse-Grain DEM Study of Monodisperse Granular Mixing

Numerical Simulation of Hydrodynamics and Mixing Characteristics of High-Viscosity Non-Newtonian Fluid in Twin-Shaft Kneaders

Investigation of the Vibrating Feeding System for Sphericity Separation of Coated Fuel Particles Using DEM

Investigation of mixing homogeneity of binary particle systems in high-shear wet granulator by DEM

DEM investigation of the axial dispersion behavior of a binary mixture in the rotating drum

Effects of operation parameters on particle mixing performance in a horizontal high shear mixer

Investigating the Flow of Rod-Like Particles in a Horizontal Rotating Drum Using DEM Simulation

Numerical Simulation of Particle Mixing Behavior in High Speed Shear Mixer and Cylinder Mixer

Numerical Study of Mixing of Binary-Sized Particles in Rotating Tumblers on the Effects of End-Walls and Size Ratios

Enhancing Mixing of Particles by Baffles in A Rotating Drum Mixer

Investigating the effects of material properties on the mixing dynamics of cohesive particles in a twin screw mixer using a discrete element method approach

Research and Optimization Design of Mixing Characteristics of High-speed Centrifugal Mixer Based on DEM

Numerical and Experimental Study of Radial Segregation of Bi-Disperse Particles in a Quasi-Two-dimensional Horizontal Rotating Drum

Investigating screw-agitator speed ratio impact on feeding performance in pharmaceutical manufacturing using discrete element method

2D DEM Simulation of Particle Mixing in Rotating Drum: A Parametric Study

Investigation of Modeling Non-Spherical Particles by Using Spherical Discrete Element Model with Rolling Friction

Comparative Study on the Characterization Method of Particle Mixing Index Using DEM Method