Abstract:Using discrete element method (DEM) modeling and near-infrared (NIR) spectroscopy, the feasibility of powder mixing in the initial pre-melting zones of a twin screw extruder using two independent feeders was studied. Previous work in the pharmaceutical and food industry has focused on mixing when materials are melted or on material homogeneity at the extruder's output. Depending on the formulation, ensuring a fully blended formulation prior to melting may be desired. Experiments were conducted using a Coperion ZSK-18 extruder to evaluate if blend uniformity can be achieved by exploring screw configuration, screw speed, and powder feed rate. As powder exited the extruder and deposited on a conveyor belt, an in-line NIR spectrophotometer measured spectra of material. Chemometric-based models predicted unknown concentrations to evaluate if blend uniformity was achieved. Using the EDEM software, Hertz-Mindlin contact model, and dimensions of the extruder, DEM simulations complemented the experimental work. The DEM computational models provided understanding of mixing patterns inside the extruder at particle scale and helped select the screw configuration before doing experimentation. The simulations showed good axial mixing for all the screw configurations studied, while good cross (radial) mixing was only observed for the screw configuration with 90-degree kneading elements. Therefore, the screw configuration with two 90-degree kneading elements was chosen for the experimental study. The RTD profiles when using a screw configuration with only conveying screw elements are comparable to a plug flow reactor (PFR), while the profiles when using kneading elements are more comparable to an ideal continuous stirred tank reactor (CSTR). For the screw configuration with 90 degrees kneading elements, the mean residence time (MRT) decreases with an increase in the screw speed. Experimental NIR spectra showed that concentrations can be predicted with an error of 2%. It was demonstrated that the twin screw extruder can provide proper dry powder mixing of two powder feed streams based on a unit dose scale, enabling continuous powder mixing prior to the melting zone in the extruder for the formulation studied with a cohesive API. This setup may also work for other types of formulations. These studies can help in developing lean hot melt as well as wet extrusion/granulation processes using twin screw extruders for the continuous manufacturing of oral solid dosage products.

Investigating the effects of material properties on the mixing dynamics of cohesive particles in a twin screw mixer using a discrete element method approach

Hydrodynamics and mixing process in a horizontal self-cleaning opposite-rotating twin-shaft kneader

Numerical Study on Particle Mixing in a Double-Screw Conical Mixer

Numerical Simulation of Hydrodynamics and Mixing Characteristics of High-Viscosity Non-Newtonian Fluid in Twin-Shaft Kneaders

A Method for Assessing Micromixing in TSE and Its Application

Studying on the Upper Limit of the Coarse-Grained DEM Model for Simulating Mixing Processes in a Rolling Drum with Complex Wall Boundary

Mixing Intensification in a Horizontal Self-Cleaning Twin-Shaft Kneader with a Highly Viscous Newtonian Fluid

Analysis of the Dispersive and Distributive Mixing Effect of Screw Elements on the Co-Rotating Twin-Screw Extruder with Particle Tracking

Investigating screw-agitator speed ratio impact on feeding performance in pharmaceutical manufacturing using discrete element method

Evaluation of the mixing performance for one novel twin screw kneader with particle tracking

An Experimentally Validated Coarse-Grain DEM Study of Monodisperse Granular Mixing

Detailed modeling and process design of an advanced continuous powder mixer

An experimentally validated DEM study of powder mixing in a paddle blade mixer

Mixing performance in a miniature conical twin screw extruder with batch filling

Three-dimensional Numerical Study of the Mixing Behaviour of Twin-screw Elements

Mechanistic understanding of the effects of process and design parameters on the mixing dynamics in continuous twin-screw granulation

Evaluation of Mixing Process in Batch Mixer Using CFD-DEM Simulation and Automatic Post-Processing Method

Study of Dynamic Flow and Mixing Performances of Tri-Screw Extruders with Finite Element Method

Investigation of Particle Mixing in a Vertical Bladed-Mixer

Dispersive Mixing Performance Evaluation of Special Rotor Segments in an Intermeshing Co-Rotating Twin-Screw Extruder by Using Weighted Probability Distributions

Dry Powder Mixing Is Feasible in Continuous Twin Screw Extruder: Towards Lean Extrusion Process for Oral Solid Dosage Manufacturing