Abstract:The passive safety commercial pressurized water reactors (PWRs), AP1000 and CAP1400 are equipped with the automatic depressurization system (ADS). The fourth stage of ADS (ADS-4) has the largest discharging capacity among the all ADS stages. During a small break loss-of-coolant accident (SBLOCA), only when the system is fully depressurized by the ADS-4 to near the containment atmospheric pressure, the in-containment refueling water storage tank (IRWST) can deliver the large coolant inventory for the long-term core cooling by its water head. Before the IRWST injection, the core reaches its minimum inventory. So the transition from the ADS-4 depressurization to the IRWST injection is a very challenging period in a SBLOCA. Therefore, to evaluate the passive system performance by the integral effect test (IET), the transition must be simulated properly. This work conducted the scaling analysis for the ADS-4 depressurization and the IRWST injection for designing the related components of the ACME IET facility. A uniform scaling law based on the existing T-branch liquid entrainment models was proposed. For scaling the onset of the IRWST injection, the requirement for reproducing the synergetic effect in an IET was introduced in order to preserve the important event/process occurrence time with the proper conditions, and the scaling laws for the full pressure IRWST injection were obtained. For investigating the transition thermal hydraulic behaviors and the ADS-4 configuration influences on the core safety, one cold leg break test and three double-ended direct-vessel-injection (DEDVI) line break tests with the different ADS-4 failure modes were selected from the ACME SBLOCA test matrix, and the main test data related to the core safety were analyzed and compared. It was found that the ADS-4 actuation significantly accelerated the system depressurization but worsened the core inventory depletion at the same time. In addition, the break condition and the ADS-4 failure mode could differently affect the system depressurization and the core level. The ACC injection during the ADS-4 depressurization in DEDVI was critical for the core level makeup. The insufficient ADS-4 venting capacity delayed IRWST injection, but also mitigated the core inventory depletion. It suggests the ADS-4 design can be potentially optimized in the passive safety system design. (C) 2019 Elsevier Ltd. All rights reserved.

Analytical Studies of Long-Term IRWST Injection Core Cooling under Small Break LOCA in Passive Safety PWR

ADS-IRWST Transient Evaluation Model for AP1000 SBLOCA Analysis

Scaling and Integral Effect Test on Transition from Depressurization to Long-Term Gravity Injection

Evaluating direct vessel injection accident-event progression of AP1000 and key figures of merit to support the design and development of water-cooled small modular reactors

Research on thermal hydraulic characteristics of reflooding process based on core multi-channel model in system analysis code

Safety Analysis in VVER-1000 Due to Large-Break Loss-of-Coolant Accident and Station Blackout Transient Using RELAP5/SCDAPSIM/MOD3.5

Analysis of Transient Characteristics and Design Improvement of the Passive Residual Heat Removal System of NHR-200-II

Analysis of AP1000 Containment Passive Cooling System During a Loss-of-coolant Accident

Experimental Investigation of Early Initiation of Primary Cooldown by Secondary-Side Depressurization in A Pwr Inadequate Core-Cooling Accident

Numerical Simulation of AP1000 LBLOCA with SCDAP/RELAP 4.0 Code

Analyses of ACME integral test results on CAP1400 small-break loss-of-coolant-accident transient

Early Mitigation Measures for High Flux Reactor Loss-of-Coolant Accidents

ICONE19-43276 Preliminary Study on In-Vessel Retention in Large-Scale Advanced PWR

Simulation of VVER-1000 Guillotine Large Break Loss of Coolant Accident Using RELAP5/SCDAPSIM/MOD3.5

Simulation Model for Investigating Safety Margin of Three-Layer Molten Pool after Late Phase In-Vessel Water Injection

The Conceptual Design of Emergency Core Cooling Scheme for Tsinghua High Flux Reactor

A SIMULATION OF SMALL BREAK LOSS OF COOLANT ACCIDENT IN NUCLEAR HEATING REACTOR BASED ON RELAP5

Preliminary Study for the Passive Containment Cooling System Analysis of the Advanced PWR

The SCDAP/RELAP5 3.2 model of AP1000 on SBLOCA

Transient Characteristics of Typical Design Basis Accidents in Integrated Small Reactor NHR200-II Using RELAP5 Model

Preliminary study on physical characteristics of single‐pass super‐critical water‐cooled reactor core