Abstract:In-Vessel Retention (IVR) strategy for nuclear reactors in case of a Severe Accident (SA) intends to stabilize and retain the corium in the vessel by using the vessel wall as a heat exchanger with an external water loop. This strategy relies on simple actions to be passively taken as soon as SA signal is raised: vessel depressurization and reactor pit flooding. Then, the strategy is successful if the vessel keeps it integrity, which means that the heat flux coming from the corium pool does not exceed the cooling capacity of the External Reactor Vessel Cooling (ERVC) at each location along the vessel wall (no vessel melt-through) and the ablated vessel wall is mechanically resistant. The main uncertainties in this IVR safety evaluation are associated to the thermal load applied from the corium pool to the vessel wall and the resulting minimum vessel thickness after ablation. Indeed, the heat fluxes distribution along the vessel wall is directly dependent on the corium stratification which occurs as aresult of thermochemical interactions in the pool: when liquid steel is mixed with UO2 and partially oxidized Zr coming from the degradation of the fuel and claddings, there is a phase separation between oxide and metal phases due to a gap of miscibility. The primordial impact of the corium behaviour in the lower plenum of the reactor vessel on the IVR safety evaluation was clearly highlighted in the Phenomena Identification Ranking Table (PIRT) on IVR performed in the frame of the European IVMR (In-Vessel Melt Retention) project (Fichot et al., 2019). As a result, the focus is made in this paper on the critical points which impact the value of the minimum vessel thickness orequivalently the maximum heat flux reached at the outer surface of the vessel wall. Efficiency of the ERVC and mechanical resistance of the vessel wall are consequently not discussed here.The main objective is to identify the generic critical situations leading to an excessive heat flux to the vessel wall and the investigation of possible means to avoid them. In this perspective, the calculations of IVR strategy done by the project partners for different reactor designs and accident scenarios were used as a database to identify and understand the occurrence of critical configurations with excessive heat flux to the vessel wall. The results of 25 sequences are used, which correspond to 9 different reactor designs: a generic PWR 900MWe, a PWR 1100MWe with heavy reflector, a generic PWR 1300MWe, a generic Konvoi 1300MWe, a generic German BWR69, aNordic BWR, a BWR-5 Mark II, a VVER1000 and a VVER440/v213. In addition, different SA integral codes (ASTEC, ATHLET-CD, MAAP -combined with MAAP_EDF and PROCOR codes for simulation of lower plenum behavior-, MELCOR and RELAP/SCDAPSIM codes) are used.

Simulation Model for Investigating Safety Margin of Three-Layer Molten Pool after Late Phase In-Vessel Water Injection

Research on Uncertainty Analysis of In-Vessel Retention Parameters in Advanced PWR

Study on stable multi-layer molten pool experiment with internal heat generation in ERVC-IVR strategy

Heat Transfer Experiment with the Prototypical Ra Number of Heavy Metallic Layer in IVR Strategy

Investigation on Three-Layer Coupled Molten Pool Heat Transfer Experiment with Three Different Materials

In-Vessel Retention of Molten Core Debris for CAP1400

ICONE19-43276 Preliminary Study on In-Vessel Retention in Large-Scale Advanced PWR

Study on the Calculation Method of Molten Pool Decay Heat Distribution under IVR Condition

Investigation of Water Injection on Molten Zirconium-Stainless Steel Pool in IVR Strategy

Analysis of critical points of the In-Vessel Retention safety evaluation

Heat transfer of film boiling on the molten metal after water injection

Experimental Investigation on Heat Transfer Characteristics of Oxide Layer of Molten Pool

Numerical study on the thermal hydraulic characteristics of ERVC system

Experimental Investigation of 3-D ERVC Process for IVR Strategy – CHF Limits and Visualization of Boiling Phenomena

Investigation on the Effect of Low Aspect Ratio on Heat Transfer Characteristics for Light Metallic Layer

Numerical Investigation on the Thermal-Hydraulic Characteristics near a Corroded Lower Head of the Reactor Vessel During IVR-ERVC

CFD study on flow-boiling characteristics and predicting critical heat flux under natural circulation conditions of IVR-ERVC

Experimental Study on Heat Transfer Characteristics of Water Injection on Molten Pool with Low Mass Fraction of Zirconium

Uncertainty analysis for two-layer and three-layer IVR model in passive PWR

CHF experiments and prediction model under subcooling flow boiling condition in passive IVR-ERVC system

Three-dimensional Experiment of Heat Transfer for Molten Oxidic Pool