Abstract:There might be a three-layer molten pool configuration with a heavy metallic layer at the bottom in the stratified molten pool configuration. Because of the decay heat in the heavy metallic layer and the relatively low critical heat flux (CHF) at the bottom of the molten pool, vessel failure could occur at the sidewall adjacent to the heavy metallic layer. The heavy metallic layer experiment was carried out using Wood’s metal or water as the simulant to analyze the heat transfer of the heavy metallic layer under different boundary conditions. The experimental apparatus mainly contains the cooling water tank, pump, valve, test section, and watercooling heat exchanger. The different cooling rates could be obtained by adjusting the valves. Wood’s metal test has a top cooling and a sidewall cooling boundary conditions, and water tests have a top heated and a sidewall cooling boundary conditions. The sidewall cooling channels were used to simulate the external reactor vessel cooling (ERVC) conditions. A three-dimension hemisphere with a radius of 1.2 m was used as the test section, and the heavy metallic layer’s height was set to 0.3 m. Heating coils were installed in the test section to simulate the decay heat in the heavy metallic layer. Besides, thermocouples were inserted in the sidewall and test section to record the temperature data. The experimental results illustrate that the melt temperature in the heavy metallic layer increases with the height. Thermal stratification is evident in the heavy metallic layer, and heat convection is limited. But the normalized melt temperature along the horizontal direction tends to be constant. When no crust formation occurs, the water test results demonstrate that the sideward heat flux increases with the polar angle. However, when the crust formation occurs in the heavy metallic layer, Wood’s metal test results demonstrate that the dominant heat transfer mode would turn from the convective heat transfer to the heat conduction. It will affect the sideward heat flux distribution that is not constant for both heat transfer modes. Consequently, the sideward heat flux would decrease with the increase of the polar angle and the maximum sideward heat flux occurs in the bottom of the test section. By comparing the experimental sideward Nusselt number with the calculated results of previous correlations, it is found that the heat transfer correlations of ACOPO, BALI, Mayinger, and UCLA could reasonably predict the average sideward Nusselt number of the heavy metallic layer when Wood’s metal or water is the simulant.

Experimental Study on Heat Transfer Characteristics of Water Injection on Molten Pool with Low Mass Fraction of Zirconium

Investigation of Water Injection on Molten Zirconium-Stainless Steel Pool in IVR Strategy

Effect of Different Conditions on Heat Transfer Characteristics of Molten Zr-Stainless Steel Pool with Water Injection

Heat transfer of film boiling on the molten metal after water injection

Three-dimensional Experiment of Heat Transfer for Molten Oxidic Pool

Experimental Investigation on Heat Transfer Characteristics of Oxide Layer of Molten Pool

Simulation Model for Investigating Safety Margin of Three-Layer Molten Pool after Late Phase In-Vessel Water Injection

Investigation on the Effect of Low Aspect Ratio on Heat Transfer Characteristics for Light Metallic Layer

Heat Transfer Experiment with the Prototypical Ra Number of Heavy Metallic Layer in IVR Strategy

SAMPO-P: A prototypical scale low-temperature experiment on two-layer melt pool heat transfer in LWR lower head

Thermal mixing enhancement of liquid metal film-flow by various obstacles under vertical magnetic field

Thermohydraulic experiments on a water jet into vacuum during ingress of coolant event in a fusion experimental reactor

Experimental Research of Heat Transfer in Heavy Metallic Layer under Different Top Boundary Conditions

Enhancement of critical heat flux with additive-manufactured heat-transfer surface

The Effects of Surface Orientation, Heater Size, Wettability, and Subcooling on the Critical Heat Flux Enhancement in Pool Boiling

A Research On Eliminating The Deposited Water After Water-Ingress Accident In Htr

Investigation on Three-Layer Coupled Molten Pool Heat Transfer Experiment with Three Different Materials

Enhancement of the Critical Heat Flux for Downward-Facing Saturated Pool Boiling on the Reticular Hollow Shell Structure Surfaces

Study on the Calculation Method of Molten Pool Decay Heat Distribution under IVR Condition

Different Heat Transfer Modes of Heavy Metallic Layer in IVR Strategy

Effect of Grooves on Nucleate Boiling Heat Transfer from Downward Facing Hemispherical Surface