Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Thermohydraulic experiments on a water jet into vacuum during ingress of coolant event in a fusion experimental reactor

Fundamental study of a water jet injected into a vacuum vessel of fusion reactor under the ingress of coolant event

Thermofluid experiments on ingress of coolant event

Thermal Hydraulic Characteristics During Ingress of Coolant and Loss of Vacuum Events in Fusion Reactors

Analysis and Experimental Results on Ingress of Coolant Event in Vacuum Vessel

Possibility of Volume Reduction of Blowdown Tank in Fusion Reactor Safety System

Numerical Study on Direct-Contact Condensation of Vapor in Cold Water

Turbulent Heat Transfer for Coolant Water Flow in Plasma Facing Component

Experimental and Numerical Studies on Heat Transfer and Fluid Flow Characteristics in A Vacuum Vessel of Fusion Reactor after the Loss-Of-Vacuum-Events Occurred

Proposal of Integrated Test Facility for in-Vessel Thermofluid Safety of Fusion Reactors

Thermohydraulic Analysis of Accident Scenarios of a Fusion DEMO Reactor Based on Water-Cooled Ceramic Breeder Blanket: Analysis of LOCAs and LOVA

Numerical Simulation of Heat Transfer and Fluid Flow of a Non-Equilibrium Argon Plasma Jet with Confined Wall

Fusion Safety Experiments in Jaeri

Progress in Thermohydraulic Analysis of Accident Scenarios of A Water-Cooled Fusion Demo Reactor

Safety scenario and integrated thermofluid test

Experiments on heat transfer of smooth and swirl tubes under one-sided heating conditions

Temperature distributions in a Tokamak vacuum vessel of fusion reactor after the loss-of-vacuum events occurred

Experimental Study on Buoyancy-Driven Exchange Flows Through Breaches of a Tokamak Vacuum Vessel in a Fusion Reactor under the Loss-of-Vacuum-Event Condition

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Investigation of cascade-type falling liquid-film along first wall of laser-fusion reactor

Thermal Mixing Test Of Coolant In The Core Bottom Structure Of A High-Temperature Engineering Test Reactor