Abstract:High-temperature proton exchange membrane fuel cell (HT-PEMFCs) has the advantages of simple hydro-thermal management, strong resistance to CO, direct feeding of reforming gas and high efficiency of cogeneration. It is one of the ideal power sources for the development of clean energy. As the core component of HT-PEMFCs, membrane electrode assembly (MEA) is mainly composed of cathode and anode gas diffusion electrode and proton exchange membrane, which determines the performance and cost of HT-PEMFCs. Therefore, optimizing the structure of gas diffusion electrode (GDE) is an important means to improve the performance and reduce the cost of HT-PEMFC. In this work, from the point of view of catalytic layer, pore-forming agent was introduced into catalytic layer to construct double catalytic layer with different pore structure. Among them, MEA 2 uses 46.7% (w) PtCo/C in the inner catalyst layer without adding pore-forming agent, and the outer catalyst layer uses 40% (w) Pt/C and adds 20% (w) pore-forming agent. It has relatively small ohmic polarization, minimum mass transfer polarization and activation polarization, and has the largest electrochemical active area, and the electrochemical performance is the best. At 160 degrees C and atmospheric pressure, hydrogen and air as fuel, the maximum power density of the single cell composed of the membrane electrode is 439 mW.cm(-2), which is 69 mW.cm(-2) higher than that of the single cell without pore-forming agent. Whether the pore-forming agent is added into the inner catalytic layer (CL) or the outer CL, the pore structure is adjusted to optimize the phosphoric acid (PA) distribution and reduce the oxygen mass transfer resistance to improve the electrochemical performance. The former catalyst layer has a greater hydrophobicity change and the electrochemical performance is more affected by the PA content, while the latter catalyst layer hydrophobicity changes less and the electrochemical performance is more affected by the oxygen mass transfer resistance. Excessive addition of pore-forming agent inside or outside CL will produce larger ohmic polarization resistance (R-Omega), and the acid drowning caused by insufficient hydrophobicity of CL will further reduce the electrochemical performance of the battery.

Design and Investigation of Dual-Layer Electrodes for Proton Exchange Membrane Fuel Cells

Construction of Homogeneous Catalyst Layers at Proton Exchange Membrane Fuel Cell Cathodes

Preparation of Membrane Electrode Assemblies for Proton Exchange Membrane Fuel Cells

An Effective Method of Applying Octahedral Pt-Ni/C to Membrane Electrode Assembly and Related In-Situ X-ray Absorption Fine Structures Study

Membrane Electrode Assembly Based on Buckypaper with Gradient Distribution of Platinum, Proton Conductor and Electrode Porosity

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

Pore-scale Investigation of Catalyst Layer Ingredient and Structure Effect in Proton Exchange Membrane Fuel Cell

Design of graded cathode catalyst layers with various ionomers for fuel cell application

Efficient Drainage Design of Cathode Catalyst Layer for Pure Oxygen Proton Exchange Membrane Fuel Cells

High-performance anode for Polymer Electrolyte Membrane Fuel Cells by multiple-layer Pt sputter deposition

Enhanced Water Management in the Cathode of an Air-Breathing PEMFC Using a Dual Catalyst Layer and Optimizing the Gas Diffusion and Microporous Layers

Numerical Simulation of Double Layered Wire Mesh Integration on the Cathode for a Proton Exchange Membrane Fuel Cell (PEMFC)

Layer-by-Layer Polydimethylsiloxane Modification Using a Two-Nozzle Spray Process for High Durability of the Cathode Catalyst in Proton-Exchange Membrane Fuel Cells

Insights into properties of non-precious metal catalyst (NPMC)-based catalyst layer for proton exchange membrane fuel cells

Design and Study on Pore Structure of Cathode Double Catalytic Layer in High-temperature Proton Exchange Membrane Fuel Cell★

Experimental Investigation of Proton Exchange Membrane Fuel Cell with Platinum and Nafion along the In-Plane Direction

Numerical Optimization of Triple-Phase Components in Order-Structured Cathode Catalyst Layer of a Proton Exchange Membrane Fuel Cell

A Study on Novel Pulse Preparation and Electrocatalytic Activities of Pt/C-Nafion Electrodes for Proton Exchange Membrane Fuel Cell

Mesostructured platinum-free anode and carbon-free cathode catalysts for durable proton exchange membrane fuel cells.

Hierarchical catalyst layer structure for enhancing local oxygen transport in low Pt proton exchange membrane fuel cells

Janus Few Layered Graphene with Asymmetric Wettability As Anti-Flooding Cathode Supports in Proton Exchange Membrane Fuel Cells