Abstract:Fuel cells on polybenzimidazole (PBI) membrane belong to high-temperature polymer-electrolyte membrane fuel cells (HT-PEMFC). When a polymer-electrolyte complex of PBI with o-phosphoric acid (PA) is applied as a proton-conducting membrane, the proton conductivity is provided without humidification above 120°C. Hydrogen-air HT-PEMFCs are able of operating effectively at 150–200°C, which allows application of technical hydrogen contaminated with CO as fuel. However, it should be noted that application of conventional "thin-film" Pt/C electrodes based on electrically conductive carbon black with Pt nanoparticles in aggressive PA environment results in electrochemical corrosion of carbon, which leads to the loss of Pt electrocatalyst particles and their aggregation (Ostwald ripening). Evidently, there is a need to replace the carbon black with more stable carbon nanostructured materials. It has been shown that self-supporting mats (essentially "felt") based on carbon nanofibers (CNF) can be used as HT-PEMFC anodes. The CNF mats were obtained in three stages. At the first stage, the nanofiber precursor material was obtained by electrospinning of solution of a copolymer of acrylonitrile with methyl acrylate (with addition of ZrCl 4 ). Then, the mats were stabilized by thermal oxidation (350°C, air). Afterwards, the CNFs were kept in Zn(NO 3 ) 2 (porogen) solution and pyrolyzed (1000 C, vacuum). To improve the proton conductivity, N-phosphonoethylated cardo poly(benzimidazole) (PBI-PhT-P) was deposited on the CNF surface which leads to an improvement in the performance characteristics of HT-PEMFC. The obtained materials were examined by electron microscopy. Their specific surface area and specific volume were investigated by the N 2 and CO 2 adsorption methods (up to 597 m 2 /g and 0.170 cm 3 /g). After Pt deposition, the CNFs were successfully tested as anodes (up to 0.4 mA/cm 2 at 625 mV) in hydrogen-air HT-PEMFC.

High-performance anode for Polymer Electrolyte Membrane Fuel Cells by multiple-layer Pt sputter deposition

High Performance PEM Fuel Cell with Low Platinum Loading at the Cathode Using Magnetron Sputter Deposition

Performance of Proton Exchange Membrane Fuel Cell Electrodes Prepared by Direct Deposition of Ultrathin Platinum on the Membrane Surface

Proton-Conducting Polymer-Coated Carbon Nanofiber Mats for Pt-Anodes of High-Temperature Polymer-Electrolyte Membrane Fuel Cell

Enhanced Catalytic Properties from Platinum Nanodots Covered Carbon Nanotubes for Proton-Exchange Membrane Fuel Cells

A Study on Novel Pulse Preparation and Electrocatalytic Activities of Pt/C-Nafion Electrodes for Proton Exchange Membrane Fuel Cell

Patchy Fe-N-C Supported Low-Loading Pt Nanoparticles As a Highly Active Cathode for Proton Exchange Membrane Fuel Cells

Fabrication and Performance Evaluation of Tubular Catalyst Layer for Proton Exchange Membrane Fuel Cell

Membrane Electrode Assembly with Ultra Low Platinum Loading for Cathode Electrode of PEM Fuel Cell by Using Sputter Deposition

Constructing Membrane Electrodes of Low Pt Areal Loading with the New Support of N-doped Carbon Nanocages for PEMFC

Improving Pt Utilization and Electrochemical Activity of Proton Exchange Membrane Fuel Cells Through Surface Modification of Carbon Nanotube Catalyst Support

Performance improvement of ultra-low Pt proton exchange membrane fuel cell by catalyst layer structure optimization

Carbon Nanofiber Gas-Diffusion Anodes Based on a Copolymer of Acrylonitrile with Methyl Acrylate for High-Temperature Polymer-Electrolyte Membrane Fuel Cell

Ionomer Cross-Linking Immobilization of Catalyst Nanoparticles for High Performance Alkaline Membrane Fuel Cells

Yolk-like Pt nanoparticles as cathode catalysts for low-Pt-loading proton-exchange membrane fuel cells

A Highly Ordered Hydrophilic–Hydrophobic Janus Bi‐Functional Layer with Ultralow Pt Loading and Fast Gas/Water Transport for Fuel Cells

Effective single web-structured electrode for high membrane electrode assembly performance in polymer electrolyte membrane fuel cell

Anode Catalytic Dependency Behavior on Ionomer Content in Direct CO Polymer Electrolyte Membrane Fuel Cell

Ultrathin Nanoporous Metal Electrodes Facilitate High Proton Conduction for Low-Pt PEMFCs

Nanostructured Ultrathin Catalyst Layer Based on Open-Walled Ptco Bimetallic Nanotube Arrays for Proton Exchange Membrane Fuel Cells

Control of self-organization of drop-casted Nafion film for improving proton conduction in a polymer-electrolyte-membrane fuel cell to raise its output power density