Abstract:The transformation from hydrocarbons to a cleaner and sustainable H 2 economy is considered a favorable approach to meet the increasing energy demand. Among different H 2 technologies, fuel cell technology is a viable option for environmentally clean energy conversion (1). Anion-exchange membrane fuel cell (AEMFC) is one of the suitable candidates to meet this demand as they could be more cost-effective than their widely used acidic counterpart, proton-exchange membrane fuel cell. For providing an affordable AEMFC, the non-precious metal catalyst (NPMC) for oxygen reduction reaction (ORR) at the cathode is needed (2). Co-doping (e.g. with N, S and Fe) of the nanocarbon material has been found to be more beneficial for the preparation of highly active ORR electrocatalysts compared to the application of just one dopant atom (e.g. N) (3). Therefore, we have prepared the polypyrrole (PPy), polythiophene (TPh), and multi-walled carbon nanotubes (MWCNT) based composite material that has been further pyrolysed and subjected to the acid treatment procedure to prepare the NPMC for the AEMFC cathode. Versatile optimization procedures were performed to finally obtain the nanocarbon material with the high ORR activity (A-PPy/PTh/MWCNT) (4). According to the scanning electron microscopy images, the composite catalyst exhibited mainly tubular morphology with PPy and PTh wrapped around the MWCNT. The physical characterization of A-PPy/PTh/MWCNT revealed the BET surface area of 379 m 2 g −1 and micro-mesoporous tubular structure. The surface composition of the catalyst was found to contain S, C, N, O and Fe, while the latter originates from the FeCl 3 polymerization catalyst. The ORR studies with A-PPy/PTh/MWCNT electrocatalyst in 0.1 M KOH showed the ORR half-wave potential of 0.85 V vs. RHE. According to the Koutecky-Levich analysis, the NPMC catalyzed a preferred 4-electron oxygen reduction pathway (4). A single-cell AEMFC experiment with A-PPy/PTh/MWCNT cathode catalyst showed the maximum power density (P max ) of 284 mW cm −2 , while the P max value of 328 mW cm −2 was recorded for commercial Pt/C in similar AEMFC conditions (Figure 1). The obtained data show that the three-component (PPy, PTh and MWCNT) composite prepared herein is a promising route for the development of AEMFC cathode catalyst (4). References A. Serov, I. V. Zenyuk, C. G. Arges and M. Chatenet, Journal of Power Sources, 375, 149 (2018). T.-W. Chen, P. Kalimuthu, P. Veerakumar, K.-C. Lin, S.-M. Chen, R. Ramachandran, V. Mariyappan and S. Chitra, Molecules, 27, 761 (2022). A. Sarapuu, E. Kibena-Põldsepp, M. Borghei and K. Tammeveski, Journal of Materials Chemistry A, 6, 776 (2018). A. Sokka, M. Mooste, M. Marandi, M. Käärik, J. Kozlova, A. Kikas, V. Kisand, A. Treshchalov, A. Tamm, J. Leis, S. Holdcroft and K. Tammeveski, ChemElectroChem, 9, e202200161 (2022). Figure 1

Carbon Nanofiber Gas-Diffusion Anodes Based on a Copolymer of Acrylonitrile with Methyl Acrylate for High-Temperature Polymer-Electrolyte Membrane Fuel Cell

Proton-Conducting Polymer-Coated Carbon Nanofiber Mats for Pt-Anodes of High-Temperature Polymer-Electrolyte Membrane Fuel Cell

Influence of the Polymer Precursor Structure on the Porosity of Carbon Nanofibers: Application as Electrode in High-Temperature Proton Exchange Membrane Fuel Cells

Unique Self-Phosphorylating Polybenzimidazole of the 6F Family for HT-PEM Fuel Cell Application

High-performance anode for Polymer Electrolyte Membrane Fuel Cells by multiple-layer Pt sputter deposition

Fluorination-enabled Interface of PtNi Electrocatalysts for High-Performance High-Temperature Proton Exchange Membrane Fuel Cells

Carbon-Nanowall Microporous Layers for Proton Exchange Membrane Fuel Cell

Ionomer Cross-Linking Immobilization of Catalyst Nanoparticles for High Performance Alkaline Membrane Fuel Cells

Designing the 3D Architecture of PGM-Free Cathodes for H2/Air Proton Exchange Membrane Fuel Cells

Nanostructured Ultrathin Catalyst Layer Based on Open-Walled Ptco Bimetallic Nanotube Arrays for Proton Exchange Membrane Fuel Cells

Polythiophene, Polypyrrole and Carbon Nanotube-Based Catalyst for Alkaline Membrane Fuel Cell Cathode

Enhanced Catalytic Properties from Platinum Nanodots Covered Carbon Nanotubes for Proton-Exchange Membrane Fuel Cells

Patchy Fe-N-C Supported Low-Loading Pt Nanoparticles As a Highly Active Cathode for Proton Exchange Membrane Fuel Cells

Polybenzimidazole (PBI) Functionalized Nanographene As Highly Stable Catalyst Support for Polymer Electrolyte Membrane Fuel Cells (Pemfcs)

Improved Performance of High‐Temperature Proton Exchange Membrane Fuel Cells by Purified CNT Nanoporous Sheets

Fabrication and Performance Evaluation of Tubular Catalyst Layer for Proton Exchange Membrane Fuel Cell

Pt Coated Vertically Aligned Carbon Nanotubes As Electrodes for Proton Exchange Membrane Fuel Cells

Performance Enhancement of Proton Exchange Membrane Fuel Cell through Carbon Nanofibers Grown In Situ on Carbon Paper

Graphitic Carbon Nitride-Graphene Hybrid Nanostructure as a Catalyst Support for Polymer Electrolyte Membrane Fuel Cells

Silica-facilitated Proton Transfer for High-Temperature Protonexchange Membrane Fuel Cells

Performance Enhancement of Air-Breathing Proton Exchange Membrane Fuel Cell Through Utilization of an Effective Self-Humidifying Platinum–carbon Catalyst