Abstract:Besides conventional structuring processes such as turning, milling or photo-chemical etching, laser processes are increasingly being used for surface structuring of metals. These laser processes differ fundamentally in that structuring is carried out either by material removal or by material redistribution. In this study, a new hybrid process of material ablation by means of pulsed laser radiation and material redistribution based on a remelting process by means of cw laser radiation is experimentally investigated. Besides an introduction to this new hybrid process, we give a detailed description of the equipment and methods used as well as surface structures produced on Ti6Al4V. A melt pool was generated on a prepared Ti6Al4V surface using cw laser radiation with a laser beam diameter of 520 mu m, laser power of 220 W, and a scanning velocity of 100 mm/s. In order to create surface structures, simultaneously, superimposed pulsed laser radiation with a laser beam diameter of 65 mu m, pulse duration of 60 ns, a maximum pulse energy of 0.35 mJ, and a pulse frequency of 50 kHz was used to evaporate small amounts of molten material from the melt pool. This localized evaporation of molten material is assumed to create vapor pressure that deforms the melt pool surface and therefore leads to surface structures. Our results indicate that by pulsed laser radiation capillary surface waves with a wavelength of the doubled laser beam diameter are excited on the melt pool surface. This forced excitation of capillary surface waves result in surface structures that are analyzed after solidification by means of white light interferometry. Based on this analysis we derived an oscillation frequency of v = 2.27 (+/- 0.16) kHz for the excited capillary surface wave as well as an effective kinematic viscosity of mu= 0.1328 cm(2)s(-1) for the damping of this surface oscillation during solidification. In terms of structural features, we achieved surface structures with heights of up to 100 mu m. Furthermore, structure height controllably scales in dependence on pulse energy and number of laser pulses as long as no ejection of molten material takes place. Finally, a comparison of the redistributed material volume per time shows that we achieved a volume redistribution rate of 28.37 mm(3)/min, which is significantly bigger than has been achieved with other laser texturing techniques so far and demonstrates the high potential of this new hybrid technique not only for surface structuring purposes.

Realization and Experimental Analysis of Electron Beam Surfi-Sculpt on Ti-6Al-4V Alloy

Primary Study on Electron Beam Surfi-Sculpt of Ti-6Al-4V

Microstructure characterisation of protrusions by electron beam surfi-sculpt on the surface of TA15 Ti alloy

Determining the influence of technological parameters of the electron-beam surfacing process on quality indicators

Investigation on surface integrity of electron beam melted Ti-6Al-4 V by precision grinding and electropolishing

Finite element simulation and experimental study of single-laser track in laser polishing of Ti6Al4V

Surface Modification and Alloying of Aluminum and Titanium Alloys with Low-Energy, High-Current Electron Beams

Modeling The Microrelief Structure of Ti6Al4V Titanium Alloy Surface After Exposure to Femtosecond Laser Pulses

Macro-micron-nano-featured surface topography of Ti-6Al-4V alloy for biomedical applications

A Surface Quality Optimization Strategy Based on a Dedicated Melt-Pool Control Via the Dashed-Scan Contouring Technique in Electron Beam Powder Bed Fusion

Performance of Ti6Al4V fabricated by electron beam and laser hybrid preheating and selective melting strategy

Tuning microstructure and enhancing corrosion property of Ti-6Al-3Nb-2Zr-1Mo alloy through electron beam surface melting

Study on the Fabrication Process of 316L Stainless Steel via Electron Beam Selective Melting

Comparison of Optical and Stylus Methods for Surface Texture Characterisation in Industrial Quality Assurance of Post-Processed Laser Metal Additive Ti-6Al-4V

Effect of laser rescanning on Ti6Al4V microstructure during selective laser melting

Effects of scanning parameters on material deposition during Electron Beam Selective Melting of Ti-6Al-4V powder

Electron Beam Impact on Microstructure and Microhardness of Ti–6Al–4V Titanium Alloy Produced by Wire Electron-Beam Additive Manufacturing Technology and Selective Laser Alloying at Simulation of Electronic-Beam Welding

PRODUCED THREE-DIMENSIONAL METAL PARTS BY ELECTRON BEAM SELECTIVE MELTING

Texturing and Phase Evolution in Ti-6Al-4V: Effect of Electron Beam Melting Process, Powder Re-Using, and HIP Treatment

Experimental investigation on the factors affecting the quality of titanium alloy overhang via selective laser melting forming

Experimental Investigation on a New Hybrid Laser Process for Surface Structuring by Vapor Pressure on Ti6Al4V