Abstract:Changes in mechanical properties of rocks at high temperatures are significant to various scientific and engineering problems, such as efficient exploration in enhanced geothermal systems (EGS) and rock mass stability in radioactive waste disposal. However, a comprehensive understanding of changes in rock mechanical behaviors at high temperatures and corresponding mechanisms, especially granites, remains unclear, which calls for the examination of micromechanical properties of the constituent minerals. This work investigates four representative minerals in granites, including quartz, plagioclase, amphibole, and biotite. The micromechanical properties of these minerals in the heating–cooling cycle were characterized in real time by using the nanoindentation technique. The morphology of samples was observed not only under real-time cyclic heating–cooling conditions, but also after thermal treatment. Subsequently, changes in structure of the minerals at elevated temperatures based on X-ray diffraction (XRD) were studied. Thermogravimetric analysis coupled with Fourier's transform infrared spectroscopy (TG-FTIR) was performed to examine physio-chemical alterations of minerals at high temperatures. The experimental results revealed that the reduced modulus and hardness of quartz decreased during heating and subsequently increased during cooling. During the heating–cooling cycle, the hardness of plagioclase varied similarly to that of quartz, but its reduced modulus increased up to approximately followed by a decrease during heating. Unlike the net decrease of modulus of quartz after exposure to the heating–cooling cycle, feldspar showed a net increase of modulus. The micromechanical properties of biotite were found to rise significantly during heating, followed by a decrease during cooling. XRD results suggested the alteration of mineral structure, including spacing of lattice planes, crystallinity, and phase transitions, which controlled the above changes in mechanical behaviors of quartz, amphibole, and plagioclase. However, the aperture of open cracks along the cleavage in biotite determined its micromechanical properties during heating and cooling. Thermally-induced microcracks were observed during heating; whereas, closure of pre-existing cracks and initiation of microcracks were found during cooling. The real-time measured micromechanical properties of minerals could relate to the macromechanical behaviors of rocks under heating–cooling conditions based on thermally-induced microcracks.

Thermal Influence on Mechanical Properties of Granite: A Microcracking Perspective

Tensile Microcracking Behavior of Granites after High Temperature Treatment by Considering the Effect of Grain Size and Mineralogical Composition

Experimental and numerical simulation study on the evolution of mechanical properties of granite after thermal treatment

Mechanical behaviour of Lac du Bonnet granite after high-temperature treatment using bonded-particle model and moment tensor

Mechanical Properties and Crack Propagation Behavior of Granite After High Temperature Treatment Based on a Thermo-Mechanical Grain-Based Model

Mechanical behavior of granite subjected to thermal treatment: insight from experiment and numerical simulation

Thermal Cracking in Granite During a Heating–Cooling Cycle up to 1000 °C: Laboratory Testing and Real-Time Simulation

Laboratory Investigation on Physical and Mechanical Behaviors of Granite after Heating and Different Cooling Rates

Microcracking behavior and damage mechanism of granite subjected to high temperature based on CT-GBM numerical simulation

The Effect of Grain Size Heterogeneity on Mechanical and Microcracking Behavior of Pre-heated Lac Du Bonnet Granite Using a Grain-Based Model

Influence of repeated heating on physical-mechanical properties and damage evolution of granite

Grain-based Coupled Thermo-Mechanical Modeling for Stressed Heterogeneous Granite under Thermal Shock

Thermal effects on prediction accuracy of dense granite mechanical behaviors using modified maximum tangential stress criterion

Experimental investigation on the mechanical properties of thermally damaged granite specimens containing pre‐existing holes

Experimental investigation on physical and tensile mechanical properties of granite after different heating/cooling treatments

Real-time Experiment Investigations on the Coupled Thermomechanical and Cracking Behaviors in Granite Containing Three Pre-Existing Fissures

Analysis of physical and mechanical behaviors and microscopic mineral characteristics of thermally damaged granite

Influence of temperature and confining pressure on the mechanical properties of granite

Real-Time Measurement of Mechanical Behavior of Granite During Heating–Cooling Cycle: A Mineralogical Perspective

Temperature driven real-time weakening and strengthening mechanisms of unconfined granite

Experimental Investigation of Physical and Tensile Mechanical Properties of Granite after Different Heating and Cooling Treatments